GE IC800SSI104P2-CE S2K Series Standalone Motion Controller

Stepper Controller Electrical Specifications

The S2K Stepper Controller (IC800STI105xx) is suitable for use on a circuit capable of

delivering not more than 5,000 rms symmetrical amperes and 130 volts maximum when

protected by RK5 class 15A fuses. Table 2-2 summarizes the Stepper Controllers

maximum continuous input power requirements. The actual input power and current is a

function of the motor's operating point and the duty cycle. 

FAULT CONDITIONS — In the event of a shortedload, shorted winding, or stalled motor, the load current will attempt to increase.

As described above, the drive current to the output stage is diverted (limiting the load current to about1 A), causing the output stage to go linear. As the junction

temperature of the output stage increases, the thermal limit circuit will become operational, further decreasing the drivecurrent.

The load current (junction temperature) is then a function of ambient temperature, state of remaining drivers,supply voltage, and load resistance.

If the fault condition is corrected, the output driver will return to its normal saturated condition. 

Short circuit protection is provided for each output for supply voltages up to 25 V.

Any program can start and stop any other program, and all programs can utilize common motion blocks. 

Engineering time is reduced and integration is simplified due to configuration and programming wizards for the controller software.

The controller has a simple diagnostic system that is displayed on a 2-character LED on the front panel. 

INDUCTIVE LOAD DRIVER — Bifilar (unipolar) stepper motors can be driven directly. 

The internal kickback diodes prevent damage to the output transistors by suppressing the high-voltage spikes which occur when

turning OFF an inductive load.

All LED status display codes are listed in the Motion Solutions manual. 

Multiple faults are displayed on a round robin basis. The S2K Series can control a wide torque range within a single model. 

The controller has a reduced package size and extensive processing power for demanding applications. 

There are 2 analog inputs and one analog output on the controller, and it comes complete with one network connection.

Refer to the manual for further information about S2K controllers.

IC800STI105D2-CE is a VersaMotion S2K controller that is manufactured by GE Fanuc Automation. 

This controller is a 4.3 ampere and 115/230 VAC device with resolver feedback and DeviceNet programming. 

This unit has discrete inputs and outputs, position feedback, an emergency stop circuit, 

a brushless servo motor, a VAC input, a serial port, auxiliary I/O, and DIP switch positions.

String variables simplify interface with third-party man-machine interfaces. 

IC800STI105D2-CE supports immediate mode operation where an external host can load registers or 

issue commands (over the serial or Network ports) that are executed in real time. 

This controller has a real-time operating system and comprehensive programming language that supports up to four programs, 

one motion task, and one communication task simultaneously executed.

We have the same series of models in stock. 

If you don't find the model you need, please contact us and we will provide you with an official quotation！

GE V7865-ACC-603-RC VME Transition Module for V7865

GE VMIVME-4116 8-channel 16-bit digital-to-analog converter board

GE VMIVME-2210 Specifications

GE VMIVME-1128 128-bit High-Voltage Digital Input Board with Built-in-Test

GE XVB603 VME Single Board Computer

GE VMIVME-4132-010 32-Channel, 12-bit Analog Output Board with Built-In-Test

GE VMIVME-2540-300  24-Channel Intelligent Counter/Controller

GE VMIVME-4514A-000 16-Channel Scanning Analog I/O Board

GE VMIACC-5595-208 Specification 

GE VMIVME-3122 High-Performance 16-bit Analog-to-Digital Converter

GE VMIVME-7805 VMEBus SBC Motherboard

GE VMIVME-2128 Output Module

GE VMIVME-3123 Specifications 

GE VMIVME-7700 Ultra Low Voltage Intel® Celeron® VMEbus

GE VMIVME-5531M VMIVME-5531L Specifications

GE VMIVME-3100 analog-to-digital conversion module

GE VMIVME-2170A Isolated Digital Output Module

GE VMIVME-7740 VME Single Board Computer

GE VMIVME-2120 64-bit High-Voltage Digital Output Megamodule

GE VMIVME-4941 Quad-Channel Synchro/Resolver-to-Digital Converter

GE VMIVME-4116 8-channel 16-bit Digital-to-Analog Converter Board

GE VMIVME-7696-650  Pentium II Processor-Based VMEbus Single-Board Computer