Emerson IC758ROWC15PCX128 Replacement Back for 15" RXi-PanelPcEmerson Bezel- 16GB RAM, 128GB SSD

The field network is wired in a ring configuration from Port A around a loop to Port B of the

network master. Beginning at Port A, the network is wired to Port A of the first actuator and

then from Port B of the first actuator to Port A of the second actuator and so on until the

network returns from Port B of the last actuator to Port B of the network master. Networks

may have parallel wired (bus wired) actuators between series wired actuators. Always wire

parallel actuators to Port A and remove termination and bias. Do not connect more than 15

actuators in parallel between any two series connected actuators. Networks are polarized with

(+) and (-) symbols on all drawings. Proper operation requires that polarity be observed at all

connections.

Connect the field networks to the Port A and B connectors on the NIM in the

network master as shown in Figure 9. The networks must be connected to Port A and Port B

of the valve actuators as shown in the wiring diagram of the XTE3000/ICON3000 IOM. Others

320B and RTS, please refer to their IOM for network wiring diagram. Controlinc 320B Quick

Start manual. Controlinc supports many different network topologies. This manual supports

only a single ring E>Net network topology that allows a combination of parallel (bus) and series

E>Net connections on the same network.

Network Master Mounting

If the system is supplied from the factory in an NEMA enclosure, no internal wiring

is required except for connecting power and field network wiring. The next three

sections (Sections 2.1. 2.2 and 2.3) discuss mounting, power input and field network

wire connections to the NIM.

Mounting of NEMA Enclosure

The enclosure is rated for NAMA 4/12 and IP65/IP55. Dimensions of the enclosure are shown

in Figure 5. Mounting dimensions are shown in Figure 6. The enclosure may be bulkhead

mounted using the internal mounting holes. External mounting brackets may be used if

desired. When mounting using the internal mounting holes, caution must be used to ensure

the holes are sealed to maintain the NEMA/IP rating. The enclosure is supplied with five 1/2 in.

compression type cable entry hubs. These may be fitted with conduit type fittings if desired.

If the system includes backup LCD keypad terminal, some planning is required to allow for

proper height above the floor to view the display and properly operate the keypad.

Daniel Woodhead Nema L6-30R Male & Female SET Watertite Yellow Rubber

Shock Set Rear Fits Simca 1300 & 1500 Woodhead 0.6844

MOLEX 884030C02M010 / 884030C02M010 

Woodhead Brad Connectivity Molex 804000A09M300 1200650295 Micro Change Cordset

Woodhead 5030 Pro-Yellow String Light 100Ft 10 Socket Kit (R00)

Wood Head partno.14w47 ERICSON part no1610-cw6p SET OF 2PC plug

Woodhead 113020A01F2002 1300100240 male female straight to straight 20ft Cordset

Woodhead SST Device Net Interface Card SST-DNP-104-2- NP

Woodhead 913103 Brad Harrison Cord set

Vintage 1970's Tanganyika African Wood Head Carving Sculpture Set of 3

Vintage M&R Set 4 Golf Club Woods & Putter Head Covers Lined

Woodhead SST-DN4-104-1 V1.2.1 Device Net Interface Card

WOODHEAD INDUSTRIES 583030A10M040 / 583030A10M040 

WoodHead 804006H09M030 Molex 1200658730 Molded Sensor Cable NiBag

BRAD HARRISON WOODHEAD 805001A09M050 MICRO-CHANGE CORDSET 5P 5M 90D 

Woodhead 804000D01M040 1200650366 4P 3A 4M Cable Set

WOODHEAD INDUSTRIES 583030A10M040 / 583030A10M040

Brad Harrison Woodhead, 103003A01F120 Replaces 40906-90 3P Male 12 Feet

WOODHEAD 102000A01F030 1300060088 2P 3FT CORD SET