CTI 2500S-26-1750 Slice I/O, Ethernet, RS232/485, 900MHz, 8DIO / 2UAI (MATURE)

The 2500S family of Slice I/O modules expands the capability of 2500 Series®

Systems to include small drops of I/O connected over Ethernet.

Slice I/O modules communicate to 2500 Series® Processors using CAMP

protocol and read/write directly to the PLC memory or I/O image table.

This allows transparent integration into the 2500 Series® system without

the requirement for any complicated configuration step. Ethernet connection

to the CPU can be accomplished using the on-board port on 2500-Cxxx

Processors, or using a 2572 / 2572-A Ethernet module. Note that when using

2572 or 2572-A modules, Slice I/O can be connected even to legacy Siemens®

and Texas Instruments PLCs.

Several models of Slice I/O are available with different mixes of I/O and with

additional communications options including RS232/485 and 900MHz radio.

Slice I/O modules feature Universal Analog Inputs which allow connection of

0-5V, 0-20mA, thermocouple, and RTD sensors. All Slice I/O modules can also

be configured to communicate over Ethernet using Modbus-TCP.

NOTE: THIS PRODUCT IS MATURE AND IS NO LONGER AVAILABLE FOR

PURCHASE.

2500 Series® Flat-Panel PCs make a good platform for integrating your

own Windows® based HMI applications into 2500 Series® Systems.

The panels are based on the latest Intel® Atom™ processor technology

and feature a high-brightness LCD panel for easy readability under

industrial conditions IMPORTANT NOTE: THIS PRODUCT WAS MATURED

ON APRIL 1. 2020 AND SHOULD NOT BE USED FOR NEW DESIGNS.

The 2500-PADP is a Power Supply Adapter that enables the use of CTI 2500

Series® power supplies within legacy Texas Instruments Series 500 I/O bases.

This adapter offers a seamless upgrade path, allowing you to modernize your

Series 500 system without a complete system replacement.

You can immediately replace failed Series 500 power supplies with reliable

and compatible CTI 2500 Series® replacements. Subsequently, when budget

and/or time permits, you can then transition to a full CTI 2500 Series® system

without losing your initial investment in the replaced power supplies.

The 2500C-8-AO is designed for CTI’s 2500 Series® Compact I/O System.

The module provides 8 outputs that can be configured for voltage or current

signals on a channel by channel basis.

Features

• 8 analog outputs

• Output ranges 0-5V, 0-10V, 0-20mA, +/-5V, +/-10V, +/-20mA

• 7 Segment Display for Module Status indication

• No user calibration

• Software Configurable Range Selection

• Uses 2500C-32F removable wiring connector

The Ethernet ports are connected to an Ethernet switch incorporated into the

2500P-ECC1 module. This switch is also connected to the Ethernet controller

on the ECC1 microprocessor. This arrangement allows devices connected to

either port to communicate with the microprocessor and allows

communications between ports. The switch also provides hardware protection

against excessive broadcast/multicast traffic.

The 2500P-ECC1 Ethernet Communications Coprocessor provides state-of-the-art

features and performance for Ethernet communication when using CTI 2500

Series® Processors. It uses a dynamic memory cache to give extremely quick

response to queries from HMI systems, with no dependence on CPU scan time.

It also provides a fully configurable interface for setting up Modbus-TCP, and

CAMP client/server communications. Most importantly, it features a completely

new facility which provides peer-peer network communications between PLCs

using a new "report on change" protocol - Network Data Exchange.

SST Woodhead SST-ESR2-CLX-RLL Ethernet Modbus/Serial Modbus Communication

Woodhead PB3-PCIe 2 SST-PB3-PCIE 1 V1.1.0 Communication card

MOLEX SST-DN4-PCIE-H / SSTDN4PCIEH 

SST 5136-PFB-PCI Profibus Communications Adapter Module

CTI 901B-2500-RBC Profibus Remote Base Controller

CTI 901B-2500-RBC Profibus Remote Base Controller

CTI Control Techniques 901D-2500-RBC Profibus Remote Base Controller

CTI 2500-RIO-B RS485 Remote Base Controller

CTI 2500C-RBC-RS485 RS485 Remote Base Controller

CTI Control Technology 901E-2589-A Input Module PCB 

WOODHEAD SST DHP-PCI V1.2.0 SD-PCI-U DATA HIGHWAY PLUS INTERFACE CARD

Molex SST-PB3-VME-2 Brad Communication Board SSTPB3VME2E

AMAT 0190-34511 REV. 08 SST woodhead DNet bus scanner DNPCPCI3U1-NC- 3V V1.3.4

WOODHEAD SST-DN3-PCU-1 DEVICENET INTERFACE CARD

SST / WOODHEAD 5136-PFB-VME PROFIBUS INTERFACE CARD 5136PFBVME NIB