MOOG D138-002-012 Main control unit

Optionally, the 914-EX can be configured for dual expansion mode, which uses two medium speed expansion

channels on the 914-HDE. This mode allows for a full 1000 Mb/s of bandwidth per Ethernet port and is ideal for

high bandwidth video over IP or GigE vision applications. Since the 914-HDE motherboard multiplexes the Ethernet

data from the 914-EX card and other expansion cards in the system, the total system bandwidth usage must be

considered, and be at (or under) the maximum optical bandwidth available for the system. Refer to Section 3.2 for

detailed information 914-X series card bandwidth usage.

The G122-824 P-I Servoamplifier is used in closed loop applications where

a proportional and/or integral amplifier is needed.

Selector switches inside the amplifier enable proportional, integral or both to be selected.

Many aspects of the amplifier’s characteristics can be selected with internal switches. 

This enables one amplifier to be used in many different applications. 

The configuration options provided are the result of many years of experience in designing and commissioning closed loop systems.

The Servoamplifier employs analog electronics. 

It accepts three input signals, two single ended and one differential.

These are summed to produce an error signal which is then amplified proportionally and also integrated.

The proportional and integral signals are switched together and output as a current or voltage to drive a servovalve.

Front panel trim pots, LED indicators and test points allow fast and easy setup and aid in trouble shooting.

The servoamplifier is housed in a compact DIN rail mounting enclosure and requires a +24V supply.

along with diagnostic information, onto a single medium speed expansion channel on the 914-HDE. This bandwidth

is dynamically shared between the two Ethernet ports, allowing for total throughput of up to 1000 Mb/s.

Selector switches inside the amplifier enable proportional, integral or both to be selected.

Many aspects of the amplifier’s characteristics can be selected with internal switches. 

This enables one amplifier to be used in many different applications. 

The configuration options provided are the result of many years of experience in designing and commissioning closed loop systems.

The Servoamplifier employs analog electronics. 

It accepts three input signals, two single ended and one differential.

These are summed to produce an error signal which is then amplified proportionally and also integrated.

The use of crimp “boot lace ferrules” is recommended for the screw terminals.

Allow sufficient cable length so the circuit card can be withdrawn from its case with the wires still connected.

This enables switch changes on the circuit card to be made while the card is still connected and operating.

An extra 100mm, for cables going outside the enclosure, as well as wires connecting to adjacent DIN rail units, is adequate.

The screw terminals will accommodate wire sizes from 0.2mm2 to 2.5mm2 (24AWG to 12AWG).

One Amp rated, 0.2mm2 should be adequate for all applications.

VMIC VMIVME-7698 VME-7698-345  SINGLE BOARD COMPUTER

VMIC VMIPC4-7301 CPU Board

602937-04 / PCB-VMIC SVG PROCESS ANALOG I-O VMIVME 4512 - 333-004512-000 G /VMIC

PCIE-5565PIORC -100000 VMIC5565 GE

VMIC VMIVME-7805  VME 7805 RC   VMIVME7805  VMIVME 7805. SKU36

GE VMIC XVB602 13200013  350-9300007867 -13200013 C W/ BVM 953-10420  PNC 1394

GE FANUC VMIC VMIVME-7750-74 0  VME-7750  VMIVME7750 VMIC 7750 SKUE2

VMIC/GE/Abaco VME7807RC?VMIV ME-7807 V7807 w/ Warranty!

VMIC VMIVME 7751 76003    VMIVME7751   332-007751-000 C   350-027751-760 03 A  

PCI-5565 VMIC5565 Front Reflection Memory Card Fast Delivery

VMIC VMIVME 4120 High-Performan ce VMEbus Circuit Module