Beckhoff EL2068 | EtherCAT Terminal, 8-channel digital output, 24 V DC, 0.5 A, with channel diagnostics

The EL2068 digital output terminal connects the binary control signals

of the automation device to the actuators at process level with electrical

isolation. This EtherCAT Terminal contains eight channels, which display

their signal status by means of LEDs. The integrated diagnostics can be

evaluated in the controller and are indicated by the LEDs. A diagnostic

bit is set for the affected channel if there is an overload.

The diagnostics serve to simplify the maintenance of the application.

In the EL2068. the outputs are supplied via the 24 V power contact.

The power contacts are looped through.

The ED2032 digital output terminal connects the binary control

signals from the automation device on to the actuators at the

process level with electrical isolation. The EtherCAT Terminal

contains two channels whose signal state is indicated by light

emitting diodes (status LEDs).

An overload detected by the integrated diagnostics can be

evaluated in the controller and is also indicated by LEDs. A

diagnostic bit is set for the affected channel if there is an

overload. The diagnostics serve to simplify the maintenance

of the application. The power contacts are looped through.

In the ED2032 the outputs are supplied via the 24 V DC power

contact. They are electrically isolated from the fieldbus side.

The ED series EtherCAT Terminals have push-in connection technology

which makes wiring easy and tool-free.

The ELX2008 digital output terminal enables the direct connection

of intrinsically safe actuators located in hazardous areas classified

zone 0/20 or 1/21. The ELX2008 supplies an output voltage of 24

V DC and a maximum output current of 30 mA per channel. 

The signal state of each channel is indicated by a light emitting diode.

EtherCAT terminals of the ELX series must always be operated in

conjunction with the ELX9560 power supply terminal. This terminal

generates an electrically isolated output voltage (24 V EX) from the

input voltage (24 V DC) for supplying the subsequent ELX terminals.

If a new power supply is required, the combination of an ELX9410

and an ELX9560 can be used so that further ELX terminals can be

added.

LTI DRIVES Compact Servo Controller CDF30.008.C2.4 8673548 DC 24-48V 1 pcs #BEV#

LUST LTI Drives Servo Drive CDA34.006.W3.0 / *SW: V3.70-04

Lust CDE34.005.W2.2 Lti Drives CDE34005W22

LUST LTI DRIVES CDA32.004.C1.4.H08.B0 Mat.-Nr.: 3084456 Software: V 160.10-01

1PC LUST LTi DRiVES CDB34.003.C2.4.PC1.H15 SERVO MOTOR DRIVER

LUST LTI DRIVES CDB32.008.W2.4.BR,PC1

LTI DRIVES Servo Controller CDF30.002.C0.7 08685963 DC 24V 1 pcs #BEV#

LUST LTI Drives CDF30.008.C2.4. M:8673548. rev:24.DC 24-48V 10A SERVO DRIVE

LTi DRIVES PM-E40.2DRA054P FW. 130.00-10 Wind Turbine Pitch Control Inverter

LUST LTi CDB32.004.C2.4.SH, LTi DRIVE REV : 24. 4A, DC24-48V SERVO DRIVE

LUST LTI Drives LST-074-2-30-320/T1. P, S4. 1R Servomotor 11722016

LUST LTI Drives LSH-097-2-30-560/T1. B, P, S4. G6.2M Servomotor 11713043