Beckhoff EL2004 | EtherCAT Terminal, 4-channel digital output, 24 V DC, 0.5 A

The ELX2002 digital output terminal enables the direct connection

of intrinsically safe actuators located in hazardous areas classified

zone 0/20 or 1/21. The ELX2002 supplies an output voltage of 

24 V DC and a maximum output current of 45 mA perchannel,

sum current is 80 mA. The signal state of each channel is indicated

by a light emitting diode.

EtherCAT terminals of the ELX series must always be operated in

conjunction with the ELX9560 power supply terminal. This terminal

generates an electrically isolated output voltage (24 V EX) from the

input voltage (24 V DC) for supplying the subsequent ELX terminals.

If a new power supply is required, the combination of an ELX9410

and an ELX9560 can be used so that further ELX terminals can be

added.

The ELX terminal segment must be terminated with one ELX9012.

two ELX9410 or one EK1110. The use of two ELX9410 allows the

use of EL terminals behind ELX terminals. With the EK1110. the

terminal segment can be continued via an EtherCAT cable,

for example to implement cable redundancy.

The safety parameters are not stored directly on the component, but are

transmitted to the input terminal via a TwinSAFE Logic capable component

when the safety application is started. This simplifies service procedures,

because the component can simply be replaced. The safety-relevant

parameters are transferred to the new component when the safety

application is restarted.

The digital EL1852 EtherCAT Terminal combines eight digital inputs

and eight digital outputs on a single device. The signal state of

the channels is indicated by LEDs. The EL1852 offers a high packing

density with 16 channels. A 20-pin contact strip enables the secure

connection of plug connectors using insulation displacement contact,

as is usual for ribbon cables and special round cables.

This significantly simplifies the wiring of many channels.

Special features:

• compact design through the combination of inputs and outputs in

one terminal

• no bouncing due to mechanical switches thanks to 3 ms input filter

• short-circuit proof outputs protected against reverse polarity with

output current up to 0.5 A

• direct connection of connectors with insulation displacement

contacts

LTI DRIVES Compact Servo Controller CDF30.008.C2.4 8673548 DC 24-48V 1 pcs #BEV#

LUST LTI Drives Servo Drive CDA34.006.W3.0 / *SW: V3.70-04

Lust CDE34.005.W2.2 Lti Drives CDE34005W22

LUST LTI DRIVES CDA32.004.C1.4.H08.B0 Mat.-Nr.: 3084456 Software: V 160.10-01

1PC LUST LTi DRiVES CDB34.003.C2.4.PC1.H15 SERVO MOTOR DRIVER

LUST LTI DRIVES CDB32.008.W2.4.BR,PC1

LTI DRIVES Servo Controller CDF30.002.C0.7 08685963 DC 24V 1 pcs #BEV#

LUST LTI Drives CDF30.008.C2.4. M:8673548. rev:24.DC 24-48V 10A SERVO DRIVE

LTi DRIVES PM-E40.2DRA054P FW. 130.00-10 Wind Turbine Pitch Control Inverter

LUST LTi CDB32.004.C2.4.SH, LTi DRIVE REV : 24. 4A, DC24-48V SERVO DRIVE

LUST LTI Drives LST-074-2-30-320/T1. P, S4. 1R Servomotor 11722016

LUST LTI Drives LSH-097-2-30-560/T1. B, P, S4. G6.2M Servomotor 11713043