GE IC693ACC303 Memory Card, 32 KBytes, Use With HHP

Overview

The built-in enhanced Ethernet interface of the Series 90-30 CPU374 PLUS provides TCP/IP  communications with: 

▪ Series 90, PACSystems, and VersaMax PLCs

▪ host computers running the Host Communications Toolkit or CIMPLICITY software

▪ computers running the TCP/IP version of the programming software.

These communications use the GE Fanuc SRTP and Ethernet Global Data (EGD) protocols

over a four-layer TCP/IP (Internet) stack.  The Ethernet interface has SRTP server capability.

As a server, the Ethernet Interface  responds to requests from devices such as PLC programming software, 

a Host computer  running an SRTP application, or another PLC acting as a client.

Series 90-30, 90-20, and Micro I/O System

The PLC I/O system provides the interface between the Series 90-30 PLC and user-supplied

devices and equipment. Series 90-30 I/O modules plug directly into slots in Series 90-30 baseplates. 

The number of Series I/O modules supported depends upon the CPU model:

• CPU models 350—374 support up to 79 I/O modules. These CPUs support up to eight racks,

which includes the CPU rack plus a total of seven expansion and/or remote racks.

• CPU models 331, 340, and 341, support up to 49 I/O modules. These CPUs support up to five

racks, which includes the CPU rack plus a total of four expansion and/or remote racks.

• CPU models 311 and 313 (5-slot baseplates) support up to 5 Series 90-30 I/O modules. 

CPU model 323 (10-slot baseplate) supports up to 10 Series 90-30 I/O modules. 

These three CPUs do not support expansion or remote racks.

The I/O structure for the Series 90-30 PLC is shown in the following figure.

CPU374 PLUS Ethernet Features 

▪ Full PLC programming and configuration services 

▪ Periodic data exchange using Ethernet Global Data (EGD) 

▪ EGD Commands to read and write PLC and EGD exchange memory over the network* 

▪ TCP/IP communication services using SRTP 

▪ Support for SRTP Client (Channels)* 

▪ Basic remote PLC monitoring from a web browser* 

▪ Comprehensive station management and diagnostic tools 

▪ Extended PLC connectivity via IEEE 802.3 CSMA/CD 10Mbps and 100Mbps Ethernet LAN port connectors 

▪ Network switch that has Auto negotiate, Sense, Speed, and crossover* detection 

▪ Direct connection to BaseT (twisted pair) network switch, hub, or repeater without an external transceiver 

▪ Protocol is stored in flash memory in the Ethernet interface and is easily upgraded through the CPU serial port 

▪ Communications with remote PLCs and other nodes reachable through routers. The gateway IP address must be configured 

▪ Internet access via web pages served up to standard web browsers* 

* enhanced Ethernet feature not available prior to CPU374 PLUS (Release 12.00)

Introduction

The PACSystems RX3i family provides advanced diagnostics and high performance I/O.

With a modular design and multiple expansion options, RX3i is the perfect I/O solution for your process, hybrid,and discrete applications.

Modular, High-Speed Performance RX3i is a rack-based system with a wide range of modules covering digital, analog, and numerous other specialty

I/O types. These pluggable and hot-swappable modules allow you to customize the right mix of I/O, 

with a variety ofvoltage ranges and current capacities supported to meet all your application needs.

Regardless of the I/O mix you choose, RX3i is built on high speed interfaces to provide rapid and consistent data transfer.

Two LEDs on the Mini Converter indicate activity on the transmit and receive lines.

The Converter Plug is required to convert the 9-pin serial port connector on the Mini Converter to

the 25-pin serial port connector on an IC647 computer, an IBM® PC-XT, or a PS/2® Personal Computer.

The IC640 industrial computer requires an additional adapter (not supplied – please contact your local PLC distributor) for use with the Mini Converter.

Tables 1 and 2 list the Mini Converter pinouts. The direction of signal flow is with respect to the Mini Converter.

The Series 90-30, 90-20, and Micro PLCs are members of the GE Fanuc Series 90 family of Programmable Logic Controllers (PLCs). 

They are easy to install and configure, offer advanced programming features, and are compatible with the Series 90-70 PLCs.

The 341 and lower Series 90-30 PLCs and Series 90-20 PLC use an 80188 microprocessor.

The 35x and 36x series of 90-30 PLCs use an 80386EX microprocessor. 

The 37x series of 90-30 PLCs use a 586 microprocessor. 

The Series 90 Micro PLC uses the H8 microprocessor. 

Both program execution and basic housekeeping tasks such as diagnostic routines, input/output scanners, and alarm processing are supported. 

The system firmware also contains routines to communicate with the programmer. 

These routines provide for the upload and download of application programs, return of status information, and control of the PLC.

In the Series 90-30 PLC, the application (user logic) program that controls the end process to 

which the PLC is applied is controlled by a dedicated Instruction Sequencer Coprocessor (ISCP). 

The ISCP is implemented in hardware in the Model 313 and higher and in software in the Model 311systems, and the Micro PLC. 

The microprocessor and the hardware-based ISCP can execute simultaneously, 

allowing the microprocessor to service communications while the ISCP is executing the bulk of the application program; 

however, the microprocessor must execute the nonBoolean function blocks.