Product Description
The TVME200 is a 6U VMEbus Carrier for up to 4 single-size or two double-size IndustryPack (IP)
modules used to build modular, flexible and cost effective I/O solutions for applications in process
control, medical systems, telecommunication and traffic control.
The TVME200 is designed in accordance to VMEbus Specification ANSI/VITA 1-1994 and the
IndustryPack Logic Interface Specification ANSI/VITA 4-1995. It guarantees compatibility with the wide
range of IndustryPacks in a VMEbus system.

IndustryPack I/O and ID spaces are mapped into the VME A16/D16 space.
IP Memory spaces are mapped into the VME A24 or A32 space. D08 and D16 accesses are
supported. If mapped in the VME A24 space, the size of the required memory space is configurable. In
VME A32 space, there is a fixed space of 8 Mbyte for each IP module.
Strobe signals of all IP modules are accessible via a 4 pin jumper block on the TVME200.
DMA, 32 bit access and 32 MHz operations are not supported.
Four 50 pin, 0.1 inch flat ribbon cable connectors mounted in the front panel of the TVME200 provide
access to all IP I/O lines. Status indicators for IP access, +5V and +/-12V are provided.
A set of 16-position rotary switches allows easy configuration of VME Short I/O and Memory
addresses. Interrupt routing from the IP slots to the VME IRQ’s can be done in two ways:
programmable by software or selection of predefined sets by a rotary switch.
The IP power lines are fuse protected by self healing fuses and RF filtered. The operating temperature
range is -40°C and +85°C.
Additional on the TVME200-20R all I/O lines of ‘IP D’ are routed to VME P2 and 14 user selectable I/O
lines of ‘IP C’ can be routed to VME P2 via a jumper field.

VME A16 Base Address
The VME A16 Base Address of the TVME200 is set by rotary switch S1 and S2.
Rotary switch S1 sets A[15:12] of the VME A16 Base Address.
Rotary switch S2 sets A[11:10] of the VME A16 Base Address.
The default value for the VME A16 Base Address is 0x6000 (S1=6. S2=0).
The TVME200 requires an address space of 1 Kbytes within the VME A16 address space. Each of the
four IP slots occupies 256 bytes within this 1 Kbytes VME A16 address space.
The address space for each IP is divided into the following areas: IP I/O space, IP ID space and the IP
IRQ and Control Register.
The IP I/O space has a size of 128 bytes. The size of the IP ID space and the IP IRQ and Control
Register depends on the position of switch S3:
With S3 = “0” to “7”, the IP IRQ and Control Registers of the TVME200 are accessible, and the size of
the IP ID space is 64 bytes. The remaining 64 bytes are occupied by the IP IRQ and Control
Registers. If switch S3 = “8” to “F”, the IP IRQ and Control Registers of the TVME200 are not
accessible, and the corresponding address range is added to the IP ID space, resulting in a size of
128 bytes for the IP ID space with S3 = “8” to “F”. This configuration is necessary for IP modules that
require access to the ID Space above the ID PROM.
Interrupts
Each IndustryPack can generate interrupts on two interrupt request lines (INT0 and INT1). The
VMEbus offers seven interrupt request level. IRQ7 has the highest priority, IRQ1 has the lowest
priority.
IP interrupt requests can be mapped to any of the 7 VME interrupt request levels. Interrupt routing
from the IP slots to the VME IRQs can be done by selection of predefined sets with a rotary switch or
programmable by software if S3 is in the range of “0” to “7”.
For more information about fully programmable interrupt mapping please refer to chapter “IP IRQ and
Control Register”.
Rotary switch S3 can be used to select predefined sets of mapping of the eight IP interrupt request
(two requests per IP slot) to the seven VME interrupt request level. The mapping selected with S3 =
“0” to “7” is mirrored at S3 = “8” to “F”. The difference is that access to the IP IRQ and Control
Registers of the TVME200 is only possible in switch position S3 = “0” to “7”. See chapter “IP IRQ and
Control Register” and chapter “VME A16 Base Address” for more details.
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved