KEBA KEVIEW V2 341/C-4400 HMI TOUCHSCREEN UNIT

KeTop T150/155 Mobile IPC HMIs

With the dramatic increase in robotics and safe collaborative

automation systems customers want one HMI that integrates

machine, motion, robotics, and safety.

Dimensioning of the power supply line:

When dimensioning the power supply line also observe the possible reduction

factors and the increased en vironmental temperatures in the interior connection

area of the charging station (see temperature rating of the supply terminals).

Under certain circumstances, this can lead to an increase of the cable cross-section

and to the adaptation of the temperature resistance of the power supply line.

Wireless Mobile IPC HMI with integrated safety

Combine your HMIs - PLC, Robot, and ERP system along with safety into one device

for simple and mobile operator control that increases productivity and safety.

The BL 250/B is a bus coupler of the Kemro-control system

It is used to op-erate modules of the system as decentralized I/O

clusters at other controls.The BL 250/B is connected with a

Host-control or another bus link modulevia K-Net. A maximum of

12 modules can be supplied and operated.

Behavior in case of an error at the BL BL 250/B

If an error occurs during start-up of the BL 250/B, the status LED

will remainon red and/or orange. In this case no K-Net bus traffic

will be possible, themodule must be exchanged.

Error states in the ongoing operation of the BL 250/B are monitored

bywatchdog. If the watchdog is triggered, it will activate a reset on

the BL 250/B and all inputs and outputs of the connected modules

will be reset to theirinitial status. The status LED of the BL 250/B

indicates red, the status LEDsof the other K-Net participants will

indicate green.

Response to module errors

A module error of one of the connected modules (e.g. HW-defect) is

de-tected by the BL 250/B and a corresponding status message is sent

to thebus master. The error is indicated on the status LED (red)

Behavior at sensor failure on a connected module

A sensor failure on an analog input of a connected module is forwarded

asstatus message to the K-Net master. The status LED of the BL

250/Bre-mains on green.

Keba D1633C E-Cpu-186B Cpu Control Circuit Board W/ D1630D

KEBA TM-240/A PLC MODULE

KEBA CU 313 Central Unit CU 313/C-SI/63036 Card 128MB TESTED

Engel Keba EC100 PLC Rack with PS244 CU211 PD242 AR181 TT081 DO321 DI325 (19821)

KEBA AR 281 ANALOGE INPUT BOARD

KEBA HT401/BENNINGER/5M/55268 TEACH PENDANT HT401BENNINGER/5M/55268

KEBA KeTop C20t-t00-Ar0-KMT Tech Pendant by Karl Mayer

KEBA DO 321 module DO 321/B

KEBA / KEBA-CU211 CPUBA-CU211 / CPU UNIT, Scratch

KEBA HAITAN SA900 Operator Panel

KEBA Kemro K2-400, DO 470/A, Part No. 054945

KEBA BL250/B PLC MODULE

KEBA analog module, AR281, AR 281

Keba Kemro K2-200 Programmable Logic Control Module Rev 09 74696

Keba Kemro K2-200 Control CP 255/X, Part. 072076

KEBA E-CPU-186B Control Circuit Board D1633C

KEBA E-SP-CCEC/22180 Panel

KEBA RS 091 POWER SUPPLY MODULE

KEBA CU211/0 25817 Ind 06

KEBA CU 212 ZENTRALBAUGRUPPE

KEBA CP 255/W Plc Module