GE Mark VIe IS220PDOAH1A Contact outputs

The Mark* VIeS Safety control is a stand-alone safety control system used by operators knowledgeable in 

safety-instrumented system (SIS) applications to reduce risk in critical safety functions. 

It is a derivative of the Mark VIe control system used in a variety of power plant applications. 

The Mark VIeS Safety control is programmed and configured with the same ToolboxST* application that is used in the Mark VIe control. 

The Mark VIeS Safety controller and distributed I/O module firmware are enhanced for safety control use. 

Specific Mark VIe control hardware has also been identified for use in safety control systems. 

While the Mark VIeS control performs the logic solving tasks for the system, it can also interface with the ToolboxST application. 

The ToolboxST application can interface with an external distributed control systems (DCS). 

It provides a means to lock or unlock the Mark VIeS control for configuration and safety-instrumented function (SIF) programming. 

This allows you to install a safety function, test it, and place the controller in Locked mode to perform safety control.

Interfaces to the Mark VIeS control must be strictly controlled to avoid interference with the operation of the system.

Data exchange to the safety control must be restricted and only used when validated by the application software. 

The Mark VIeS control was designed and certified to meet functional safety standards according to IEC 61508 Parts 1 through 3. 

It is certified for use in both high-and low-demand applications. 

The Mark VIeS control uses redundant architecture configurations and a hardware fault tolerance (HFT) of 1 to achieve safety integrity level (SIL) 3.

The highest achievable SIL with an HFT of 0 is SIL 2.

INSTALLATION:

Securely mount the desired terminal board.

Directly plug one PDIA I/O pack for simplex or three PDIA I/O packs for TMR into the terminal board connectors.

Mechanically secure the packs using the threaded studs adjacent to the Ethernet ports. 

The studs slide into a mounting bracket specific to the terminal board type.

The bracket location should be adjusted such that there is no right-angle force applied to the DC37 connector between the pack and the terminal board.

The adjustment should only be required once in the life of the product.

Plug in one or two Ethernet cables depending on the system configuration.

The pack will operate over either port. If dual connections are used, the standard practice is to connect ENET1 to the network associated with the R controller.

Apply power to the pack by plugging in the connector on the side of the pack.

It is not necessary to insert this connector with the power removed from the cable as the I/O pack has inherent soft-start capability that controls the current inrush on the power application.

COMPATIBILITY:

PDIAH1A is compatible with five types of discrete contact input terminal boards, including the TBCI boards, TICI boards, 

and STCI boards, but not the DIN-rail mounted DTCI board. Control mode refers to the number of I/O packs used in a signal path:

One I/O pack and one or two network connections are used in Simplex.

Dual uses two I/O packs with one or two network connections.

Three I/O packs with one network connection each are used by TMR.

Bently 3500/65 145988-02  

ABB  PF900-NR 3BDH000357 

ABB  HS810 3BDH000305R0101 

ABB  VIPA972-0DP01 

YASKAWA CACR-SR07BE12M  

ABB S-073N 3BHB009884R0021 

ABB 3BHL000986P0006  

ABB 5SDF1045H0002 

ABB 5SDF0860H0003 

ABB 5SHY3545L0010 3BHB013088R0001 3BHE009681R0101 GVC750BE101  

XP POWER  F8B6D4A3G3  

Triconex 8310  

TRICONEX 4351B 

TRICONEX 3721 

TRICONEX 3700A 

TRICONEX 4351A 

TRICONEX 4351B 

TRICONEX 3503E 

TRICONEX 3008 

TRICONEX 3664 

TRICONEX 8310N2  

ABB XUD194 XUD194A 3BHC018137R0001   

ABB PCD530A102 3BHE041343R0102  

TRICONEX MP3009  

YOKOGAWA AAI141-H50 S2  

TRICONEX 3625