GE IC800SSI107S1-CE S2K Series SERVO DRIVE

Installing the Motor

The S-Series and MTR-Series servo motors are designed for either vertical or horizontal

mounting and have a protection rating of IP65 (not including the connectors and shaft). The

motors should be mounted in a location where the environmental conditions are within the

specifications stated in Chapter 2. Use the following guidelines when mounting the motors:

•Observe the shaft radial and thrust load limits. Loads exceeding these limits will cause

premature failure of the motor. Excessive belt tension could cause bearing or shaft failure.

•Be sure to ground the motor using the ground wire in the motor power cable.

•Ensure that the motor cables are free from excessive stress, stretching, pinching or bending.

•To avoid damage, do not carry a motor by holding the cables or shaft.

•Do not apply excessive axial force or impact loads when installing the motor coupling or

shaft pulley, or the encoder may be damaged. See axial load limit ratings in Chapter 2.

•Install the motor in a location free from corrosive contaminants, dust, excessive water

spray, or combustible gas.

•The shaft of the S-series servo motor is treated with grease (Shell Oil Alvania No. 2) for

corrosion protection during storage. Consider the effect of the grease on any plastic parts

that are mated with the shaft.

•The optional servo motor brake should be used for holding stationary loads only. Do not

use this brake to stop a moving load, or reduced life or damage to the brake may occur.

Apply this brake only after the motor is stopped.

Heat Load and Cooling

The heat load of the S2K Series controllers is dependent on the model as shown below:

Stepper Controller

Model SSI105: Heat Load = 20 Watts + (0.3 * current setting in percent) or 50 watts max.

Servo Controllers

Model SSI104: Heat Load = 25 watts + (35 * duty cycle) watts or 60 watts max.

Model SSI107: Heat Load = 35 watts + (65 * duty cycle) watts or 100 watts max.

Model SSI216: Heat Load = 50 watts + (150 * duty cycle) watts or 200 watts max.

Model SSI228: Heat Load = 60 watts + (280 * duty cycle) watts or 340 watts max

Model SSI407: Heat Load = 35 watts + (65 * duty cycle) watts or 100 watts max..

Model SSI420: Heat Load = 60 watts + (250 * duty cycle) watts or 310 watts max.

Duty cycle is defined as the percent of time the controller is at full rated output divided by the

total cycle time. The SSI104 and SSI107 controllers are designed to operate at full rated

current with only natural convection cooling at ambient temperatures up to 50°C. The

SSD104, SSD107, SSI104, SSI107, SSI216, SSI228, SSI407, SSI420 and STI105 models

have built-in fan cooling.

The controllers must be installed vertically for effective cooling. Allow a minimum clearance of

3 inches above and below the unit. A minimum of 2 to 3 inches clearance is also

recommended on the right and left sides of the unit where possible.

Note: For UL approved installation of the following controllers, maximum ambient

temperature is 40°C (104°F): IC800SSI216P2, IC800SSI216RP2, IC800SSI216D2,

IC800SSI216RD2, IC800SSI228P2, IC800SSI228RP2, IC800SSI228D2,

IC800SSI228RD2, IC800SSI407RS1, IC800SSI407RP2, IC800SSI407RD2,

IC800SSI420RP2, IC800SSI420RD2

We have the same series of models in stock. 

If you don't find the model you need, please contact us and we will provide you with an official quotation！

GE IC800SSD104RS1-CC S2K Series Standalone Motion Controller

GE IC800SSI104RS1-CE VersaMotion S2K controller

GE IC800SSI104RD2-CE S2K Series Standalone Motion Controller

GE IC800SSI104RP2-CE VersaMotion S2K controller

GE IC800SSD107S1-CC VersaMotion S2K controller

GE IC800SSI107S1-CE S2K Series Standalone Motion Controller

GE IC800SSI107D2-CE S2K Series Standalone Motion Controller

GE IC800SSI107P2- CE VersaMotion S2K controller

GE IC800SSD107RS1-CC VersaMotion S2K controller

GE IC800SSI107RS1-CE S2K Series Standalone Motion Controller

GE IC800SSI107RD2-CE VersaMotion S2K controller

GE IC800SSI107RP2-CE VersaMotion S2K controller

GE IC800SSD216S1-EC S2K Series Standalone Motion Controller

GE IC800SSI216D2-EE VersaMotion S2K controller

GE IC800SSI216P2-CE S2K Series Standalone Motion Controller

GE IC800SSD216RS1-EC VersaMotion S2K controller

GE IC800SSI216RD2-CE S2K Series Standalone Motion Controller

GE IC800SSI216RP2-CE VersaMotion S2K controller

GE IC800SSD228S1-CC VersaMotion S2K controller

GE IC800SSI228D2-CE VersaMotion S2K controller

GE IC800SSI228P2-CE VersaMotion S2K controller

GE IC800SSD228RS1-CC VersaMotion S2K controller

GE IC800SSI228RD2-CE S2K Series Standalone Motion Controller

GE IC800SSI228RP2-CE VersaMotion S2K controller

GE IC800SSD407RS1-EE S2K Series Standalone Motion Controller