ABB 2VAA008431R11 RDO01A Red. DO 16-CH 24/48VDC max 250mA

Features and benefits

Termination for up to eight (8) analog I/O process signals within a horizontal row.

All SD I/O modules & bases of all types (Singular or Redundant) AND (Compact or Full-size), are

100% fully compatible with each other. Thus, Singular & Redundant, Compact or Full-size I/O

modules can be mounted within a single, common HN800 I/O bus.

Optional mechanical keying can be implemented to prevent insertion of the wrong I/O module

type.

Latching device on the base locks the base into position on DIN-Rail.

Industry standard 35-mm DIN rail, Horizontal row mounting.

Time Synchronization

Enable Time Synchronization

Determines whether or not the Server receives and sends the time synchronization 

on the network. When enabled, the Server is in time synchronization with the 

control network.

Accuracy

Time synchronization accuracy of the Server is valid when the Server is in time 

synchronization mode. The options are:

• Low accuracy (lowest accuracy); priority 0.

• Low accuracy battery backed; priority 3.

• High accuracy battery backed; priority 6.

• IIOIS20 node; priority 9.

• IIOIS20 SCSI; priority 10.

• PIMS SCSI; priority 11.

• Satellite clock system (highest accuracy); priority 12.

These accuracy settings are only used when negotiating for time mastership with 

other nodes in the underlying Harmony control network.

Master Update Period

Master update period is the frequency that Harmony Server synchronizes time with 

the underlying Harmony control network. This property is used only when Time 

Synchronization is enabled. The permissible values are 120 to 3540 seconds.

Message Wait Period

Message wait period is the Period that Harmony Server waits before attempting to 

assume time mastership on the control network. This property is used only when 

Time Synchronization is enabled. The permissible values are between 180 and 3660 

seconds. Additionally, the configured value must greater than the Master Update 

Period.

Sending Global Alarm Acknowledgement Messages to the Loop

Enable Tag Acknowledgment Broadcast 

To broadcast an alarm acknowledgement for a specific Harmony tag: 

– Select the Tag Acknowledgment Broadcast Enable check box on the  Harmony Tab of the tag. Selecting the 

checkbox enables the connectivity server to broadcast the alarm  acknowledgement for this tag on the communication highway.  

Enable Acknowledgment Transmission 

Configure the module status tag for each node to which the connectivity server  transmits the alarm acknowledgment messages. 

For each module status tag, on the  Module tab, select the Enable Alarm Acknowledgment 

Transmission check box to  have the connectivity server transmit any recently acknowledged alarms.

Broadcasts  will only be sent to a node when the corresponding module status tag is configured  and has alarm acknowledgment transmission enabled.  

Receiving Global Alarm Acknowledgement from the Loop 

Configure the Harmony Server tag to enable receiving global alarm  acknowledgment messages from other nodes on the loop. 

On the Harmony tab, select the Global Alarm Acknowledgement check box to  

enable the connectivity server to process the Global Alarm Acknowledgement  messages received through the INFI-NET loop. 

The connectivity server applies the alarm acknowledgement to the harmony tag that  has the same Harmony address as the broadcast tag.

You may need the following additional products：

A-B 1769-L18ERM-BB1B CompactLogix 5370 L1 Controller

A-B 1769-L18ERM-BB1BK CompactLogix 5370 L1 Controller

A-B 1769-L19ER-BB1B CompactLogix 5370 L1 Controller

A-B 1769-L19ER-BB1BK CompactLogix 5370 L1 Controller

A-B 1769-L24ER-QB1B CompactLogix 5370 L2 Controller

A-B 1769-L24ER-QBFC1B CompactLogix 5370 L2 Controller

A-B 1769-L24ER-QBFC1BK CompactLogix 5370 L2 Controller

A-B 1769-L27ERM-QBFC1B CompactLogix 5370 L2 Controller

A-B 1769-L30ER CompactLogix 5370 L3 Controllers

A-B 1769-L30ERK CompactLogix 5370 L3 Controllers

A-B 1769-L30ERM CompactLogix 5370 L3 Controllers

A-B 1769-L30ERMK CompactLogix 5370 L3 Controllers

A-B 1769-L30ERMS CompactLogix 5370 L3 Controllers

A-B 1769-L30ER-NSE CompactLogix 5370 L3 Controller

A-B 1769-L32E EtherNet Processor

ABB SPK800-PBAT-03 HN800 to PBA to HN800 Cable 3.0 M

ABB SPK800-PBAT-04 HN800 to PBA to HN800 Cable 4.0 M

ABB SPK800-PBAT-0A HN800 to PBA to HN800 Cable 0.5 M

ABB SPRIORBX01K01 HN800 Remote I/O Kit Non-Redundant

ABB SPRIORBX01K02 HN800 Remote I/O Kit Redundant

ABB TER800 HN800 or CW800 Bus Terminator

ABB TER800A HN800 or CW800 Bus Terminator

ABB TER810 HN800 or CW800 Bus Terminator with cover

ABB TER810A HN800 or CW800 Bus Terminator with cover