A-B 1769-L32E EtherNet Processor

See the controller installation instructions for more information about 

using these utilities to load firmware. If you load firmware via an 

EtherNet/IP connection, browse through the Ethernet port, across the 

virtual backplane, and select the 1769-L35E controller.

Loading 1769-SDN Firmware

If you are using a 1769-L35E controller and a 1769-SDN scanner for 

DeviceNet communications and want to take advantage of the new 

explicit messaging feature, you must also upgrade the scanner’s 

firmware to revision 2.2 or later. The updated firmware is available 

with RSLogix 5000 software or you can download it from the support 

website. Use the ControlFlash utility (as described above) to load the firmware.

You must use a DeviceNet connection to update the 1769-SDN 

firmware to revision 2.2. After the firmware is updated to revision 2.2, 

subsequent updates to the 1769-SDN firmware can be initiated via a 

controller backplane connection.

Hold Last State and 

User-Defined Safe State 

Not Supported

When 1769 Compact I/O modules are used as local I/O modules in a 

CompactLogix system, the local I/O modules do not support the Hold 

Last State or User-Defined Safe State features, even though you can 

configure these options in the programming software.

• If a local I/O module fails such that its communication to the 

controller is lost, or if any module is disconnected from the 

system bus while under power, the controller will go into the 

fault mode. All outputs turn off when the system bus or any 

module faults.

• RSLogix 5000 software creates tags for modules when you add 

them to the I/O configuration. The 1769 module tags define 

configuration (C) data type members which may include 

attributes for alternate outputs. CompactLogix does not enable 

local modules to use the alternate outputs. Do not configure the 

attributes listed below:

Any 1769 Compact I/O modules used as remote I/O modules in a CompactLogix system do support the Hold Last State and User-Defined Safe State features.

ATTENTION: 

•Before installing, configuring, operating or maintaining this product, read this 

document and the documents listed in the Additional Resources section for 

installing, configuring, or operating equipment. Users should familiarize 

themselves with installation and wiring instructions in addition to requirements 

of all applicable codes, laws, and standards.

• Installation, adjustments, putting into service, use, assembly, disassembly, and 

maintenance shall be carried out by suitably trained personnel in accordance with 

applicable code of practice. In case of malfunction or damage, no attempts at repair 

should be made. The module should be returned to the manufacturer for repair. Do not 

dismantle the module.

• This equipment is certified for use only within the surrounding air temperature range 

of 0…60 °C (32…140 °F). The equipment must not be used outside of this range.

• Solid state equipment has operational characteristics differing from those of 

electromechanical equipment. Safety Guidelines for the Application, Installation and 

Maintenance of Solid State Controls, publication SGI-1.1, available from your local 

Rockwell Automation sales office or online at 

http:/www.rockwellautomation.com/literature describes some important differences 

between solid state equipment and hard-wired electromechanical devices.

T9120 Eurocard Processor module 80 1.43

T9501 Eurocard Digital Input module, 24Vdc, 8Ch, isolated 94 1.21

T9531 Eurocard Analogue Input module, 8Ch, isolated 94 1.21

T9551 Eurocard Digital Output module, 24Vdc, 8Ch, isolated, 

T9581** Eurocard Analogue Output module, 2Ch, isolated 86 1.33

T9100 Processor Base D2, E2, F2, G2 968/FSP 1910.00/19 Valid

T9110 Processor Module

T9110 ControlFLASH Firmware for the Processor Module 

T9110 Recovery ControlFLASH

T9300 I/O Base Unit

T9401 Digital Input Module, 24Vdc, 8 Channel, Isol

T9402 Digital Input Module, 24Vdc, 16 Channel,

T9431 Analogue Input Module, 8 Channel, Isolated

T9432 Analogue Input Module, 16 Channel, Isolated

T9451Digital Output Module, 24Vdc, 8 Channel,Commoned

T9481 Analogue Output Module, 3 Channel

T9482 Analogue Output Module, 8 Chan

T9801 Digital Input TA, 16 Channel, Simplex,Commoned

T9802 Digital Input TA, 16 Channel, Dual, Isolated

T9803 Digital Input TA, 16 Channel, TMR, Isolated

T9831Analogue Input TA, 16 Channel, Simplex,Commoned

T9832 Analogue Input TA, 16 Channel, Dual, Isolated

T9833 Analogue Input TA, 16 Channel, TMR, Isolated

T9851 Digital Output TA, 8 Channel, Simplex,Commoned

T9852 Digital Output TA, 8 Channel, Dual, Commoned

T9881 Analogue Output TA, 8 Ch, Simplex, Commoned

T9882 Analogue Output TA, 8 Ch, Dual

T9030 OPC Portal 

T9082U IEC 61131 Workbench, USB, 1 User, 1Controller

T9082D IEC 61131 Workbench, Hard Drive, 1 User, 1Controller

T9083U IEC 61131 Workbench, USB, 1 User, Unlimited Controllers