A-B 1756-OB32 module Rockwell ControlLogix 32 digital output

Universal Remote I/O (RIO) Network 

The strength and versatility of the Universal Remote I/O network comes from the breadth of products it supports. 

In addition to 1746 I/O, the Universal Remote I/O network supports many Allen-Bradley and third-party devices. 

Typical applications range from simple I/O links with controllers and I/O, to links with a wide variety of other types of devices. 

You connect devices through remote I/O adapter modules or built-in remote I/O adapters. 

Using the Universal RIO Network instead of direct-wiring a device over a long distance to a local I/O chassis reduces installation, 

tart-up, and maintenance costs by placing the I/O closer to the sensors and actuators. 

SLC 5/03, 5/04, and 5/05 processors support pass-thru which lets you configure RIO devices remotely from an Ethernet, 

DH+, or DH-485/DF1 network, as well as block transfer instructions for faster reading and writing of I/O data. 

Serial Network 

The SLC 5/03, SLC 5/04, and SLC 5/05 processors have a serial port which is

configurable for RS-232 compatible serial communication. Use the serial port to connect

to devices that:

• communicate using DF1 protocol, such as modems, communication modules,

programming workstations, or other Encompass partner devices.

• communicate using DH-485 protocol.

• send and receive ASCII characters, such as ASCII terminals, bar code readers, and printers.

When configured for system mode, the serial port supports DF1 protocol. Use system

mode to communicate with other devices on the serial link. You can select the following

DF1 modes:

• DF1 full-duplex: provides communication between an SLC 500 controller and other

• DF1 compatible devices. In point-to-point mode, the SLC 500 controller uses

DF1 full-duplex protocol.

• DF1 half-duplex master: polls and transmits messages between the master and

each remote node. In master mode, the SLC 500 controller uses DF1 half-duplex polled protocol.

• DF1 half-duplex slave: uses the controller as a slave station in a master/slave serial network. 

In slave mode, the SLC 500 controller uses DF1 half-duplex protocol.

DF1 radio modem: a hybrid between DF1 full-duplex and DF1 half-duplex, 

this protocol is optimized for use with radio modem networks.

Selecting a ControlLogix System

The ControlLogix system architecture provides sequential, process, and

motion control together with communications and state-of-the-art I/O in a

small, cost-competitive package. The system is modular, so you can design,

build, and modify it efficiently - with significant savings in training and engineering.

A ControlLogix system can be anything from a simple chassis to a highly-distributed

system consisting of multiple chassis and networks working together.

A simple ControlLogix system consists of a stand-alone controller and I/O modules in a single chassis.

Or you can use the ControlLogix system as a gateway. Include the

communication modules you need for connectivity to other networks. For

this use, a controller is not required. The ControlLogix Gateway integrates

into existing PLC-based systems so that users with existing networks can

send or receive messages to or from other networks.

For a more robust system, use:

• multiple controllers in a single chassis

• multiple controllers joined across networks

• I/O in multiple platforms that is distributed in many locations and

connected over multiple I/O links

The 1747-BSN features:

• backup of one Remote I/O or DH+ network per complementary BSN module pair.

• backup of one RS-232/DH-485 communications per complentary BSN module pair,

• allowing HMIs on channel 0 to automatically transfer to the primary processor.

• transfer of up to 2 K words of retentive data per BSN.

• repair of primary system fault during secondary backup system operation.

• remote programming capability of secondary processor on DH+ (SLC 5/04 only).

• minimal user program impact.

• backup system diagnostic information.

Ethernet Network

The TCP/IP Ethernet network is a local-area network designed for the high-speed exchange of information 

between computers and related devices. With its high bandwidth (10 Mbps to 100 Mbps), 

an Ethernet network allows many computers, controllers, and other devices to communicate over vast distances. An Ethernet network

The 1747-BSN module contains the full complement of RIO scanner features, plus

backup capability for support of redundant processor applications. The backup system

consists of one or more pairs of complementary modules, with one module residing in the

primary system and the other in the backup system. The primary system controls the

operation of remote I/O, while the backup system monitors communications via the

high-speed serial link (HSSL) and is available to take control in the event of a fault in the primary system.

Direct Communication Module

The 1747-DCM module links the SLC 500 controller to the Allen-Bradley PLC for

distributed processing. The DCM acts as a remote I/O adapter on a remote I/O link.

Information is transferred between a local PLC or SLC scanner and a remote

1747-DCM module during each remote I/O scan. The number of DCMs that a scanner

can supervise depends on the number of chassis the scanner supports and the chassis size

of the DCM. The SLC 500 module controllers support multiple DCMs.

Note: An important distinction between a DCM module and the 1747-ASB module is

that a DCM is placed in the chassis with the processor and it does not scan any I/O in the

chassis as an ASB module does.

You may also need the following related products：

1756-OB32 module Rockwell ControlLogix 32 digital output

1756-OB8 module Rockwell ControlLogix 8 digital output

1756-OB8EI module Rockwell ControlLogix 8 digital output

1756-OB8I module Rockwell ControlLogix 8 digital output

1756-OC8 module Rockwell ControlLogix 8 digital output

1756-OF4 module Rockwell ControlLogix 4 analog

1756-OF6CI module Rockwell ControlLogix 6 analog

1756-OF6VI module Rockwell ControlLogix 6 analog

1756-OF8 module Rockwell ControlLogix 8 analog

1756-OF8H module Rockwell ControlLogix 8 analog

1756-OG16 module Rockwell ControlLogix 16 digital output

1756-OH8I module Rockwell ControlLogix 8 digital output

1756-ON8 module Rockwell ControlLogix 8 digital output

1756-OV16E module Rockwell ControlLogix 16 digital output

1756-OV32E module Rockwell ControlLogix 32 digital output

1756-OW16I module Rockwell ControlLogix 16 digital output

1756-OX8I module Rockwell ControlLogix 8 digital output

1756-PA72 Module Rockwell ControlLogix AC Power Supply

1756-PA75 Module Rockwell ControlLogix AC Power Supply

1756-PA75R Module Rockwell ControlLogix AC Power Supply

1756-PAR2 Module Rockwell ControlLogix AC Power Supply

1756-PAXT Module Rockwell ControlLogix XT Power Supply

1756-PB72 Module Rockwell ControlLogix DC Power Supply

1756-PB75 Module Rockwell ControlLogix DC Power Supply

1756-PB75R Module Rockwell ControlLogix DC Power Supply

1756-PBR2 Module Rockwell ControlLogix Power Supply

1756-PBXT Module Rockwell ControlLogix XT Power Supply