A-B 1756-L61 Module Rockwell ControlLogix 2 MB Memory Control

RTD Error

Module error on the 1756-IR6I module is defined in ohms and is calculated across 

the entire input range that is selected, not the available range of a sensor used with the module. 

For example, if the 1…487  input range is used, the module error is calculated across 507 (actual range = 0.86…507.86 ).

The error in ohms translates to temperature, but that translation varies because the

relationship is non-linear. The most effective way to check a 1756-IR6I module 

error is to calculate the error in ohms and use that value in a linearization table to check the temperatureerror.

If the module is calibrated at operating temperature and the operating temperature remains relatively stable, 

calibration accuracy is better than 0.1% of the full range for the first year after calibration. 

This 0.1% value is a worst case value. In other words, with the 1…487input range that is selected, 

the worst case module error is 0.507.

The I/O configuration portion of the RSLogix 5000® programming software generates the

configuration data for each I/O module in the control system, 

whether the module is in a local or remote chassis. 

A remote chassis, also known as networked, contains the I/O module but not the module’s owner-controller.

A remote chassis can be connected to the controller via a scheduled connection on the ControlNet network or an EtherNet/IP network.

RSLogix 5000 configuration data is transferred to the controller during the program 

download and later transferred to the appropriate I/O modules. 

I/O modules in the local chassis, and modules in a remote chassis connected via the EtherNet/IP network, 

or unscheduled connections on the ControlNet network, are ready to run as soon as the configuration data has been downloaded. 

However, to enable scheduled connections to I/O modules on the ControlNet network, 

you must schedule the network by using RSNetWorx for ControlNet software.

Running RSNetWorx™ software transfers configuration data to I/O modules on a 

scheduled ControlNet network and establishes a network update time (NUT) for the 

ControlNet network that is compliant with the desired communication options specified for each module during configuration.

Anytime a controller references a scheduled connection to I/O modules on a scheduled

ControlNet network, you must run RSNetWorx software to configure the ControlNet network.

See the following general steps when configuring I/O modules.

1. Configure all I/O modules for a given controller by using RSLogix 5000 programming

software and download that information to the controller.

2. If the I/O configuration data references a scheduled connection to a module in a 

remote chassis that is connected via the ControlNet network, 

run RSNetWorx for ControlNet software to schedule the network.

3. After running RSNetWorx software, perform an online save of the RSLogix 5000 project

so the configuration information that RSNetWorx software sends to the controller is saved.

You may also need the following related products：

NEC FC-9821X Bus expansion module

SCHROFF MPS022 Power Supply

SIEMENS 1FT5066-0AC71-2-Z Motors

SIEMENS 6DD1645-0AE1 Simadyn

SUMITOMO MC-550 MCU Sumitomo MX Power Amp Unit

SIEMENS 6AV66440AB012AX0 touchscreen

KONGSBERG HD 13T21 STD-EA1-FAGP-10051 monitor

CONCURRENT TECHNOLOGY VP325 02X module

SIEMENS 1FT5102-0AF71-1-Z Motors

COGNEX VPM-82403X Image Processing Board

COGNEX VPM-82403X/P-6000 process board

PACIFIC 6445-001-K-N module

DEIF SCM-1 module

SIEMENS 6FC5371-0AA10-0AA2 module

BASLER ELECTRIC DECS-200-2L Reed Controller

SIEMENS 6ES7416-3ES06-0AB0 module

SIEMENS 6GF6233-6MB touchscreen

HIMA F60 MI 24 01

HIMA F8627X

WESTINGH 1C31194G01 module

WESTINGH 1C31197G01 module

KOLLMORGEN SR30200-000000 drives

KOLLOMORGER AKM54K-ANC2AA00 Motors

PACIFIC SCIENTIFIC PC834-001-T

WESTINGH IC31224G01 module

WESTINGH IC31227G01 module