Honeywell 05701-A-0313 Modbus Interface Module Kit RS232

In a system where the field wiring is required to be connected to the

rear of the system, the rack is centrally divided into front and rear

sections by a printed circuit board backplane which provides common

power and signal routeing between individual Channel Control Cards.

Channel Control Cards are fitted at the front of the rack while Interface/

Relay cards are fitted directly behind the Channel Control Cards at the

rear of the rack. The Channel Control Cards and their respective

Interface/Relay Cards are interconnected by a plug and socket arrangement.

In a system where the field wiring is required to be connected to the

front of a system, the Channel Control Cards and Interface/Relay

Cards are mounted one above the other in a 6U rack. The backplane

printed circuit board still provides the common power and signal

routeing between the individual Channel Control Cards while short

cables at the rear of the cards connect each Channel Control Card to

their respective Interface/Relay Card.

Simple calibration and checking of the system is carried out using

push buttons on the Engineering Card fitted to each rack. More

complex configuration can be carried out using the RS232 link between

the Engineering Card and an external IBM compatible personal

computer running the engineering interface software.

Additional functions can be provided by the Engineering Card using

optional modules that plug into the Engineering Card. See the following

module operating instruction manuals:

05701M5006 Modbus Interface Module

05701M5007 Event Printing Module

05701M5008 Master Alarm Update Module

The 5701 Control System is shown in Figure 1 with an overview at Figure 2.

CONSTRUCTION

The system consists of individual 1'' (2.54cm) wide cards fitted to a

rigid custom rack designed to fit Euro rack cabinets. Two rack widths

are available:

a. 19 inch with 17 card slots to house up to 16 Channel Control Cards

and an Engineering Card.

b. Half 19 inch with nine card slots to house up to eight Channel

Control Cards and an Engineering Card.

Each sub-rack contains an Engineering Card and a DC Input Card to

make up the rack system

The system is designed to meet the differing customer wiring

configurations and to achieve this the control functions are split away

from the relays and field wiring connections. A single channel of gas

detection therefore consists of:

a. Sensor Drive Module

In order to achieve compatibility with a range of different inputs and

sensor types, the circuitry necessary to control the sensor is

housed on an independent plug-in Sensor Drive Module. These

modules plug directly into a Channel Control Card and are factory

fitted. There are two different modules, one for catalytic inputs and

one for 4 - 20mA inputs.

b. Single Channel Control Card

Each Single Channel Control Card functions independently and

contains all the necessary electronic circuitry to provide the sensor

drive, alarm detection and gas level display for that channel of gas

detection.

c. Field Interface or Relay Card

The Field Interface/Relay Cards provide the interface connections

between the Control Cards and their respective field connected

gas sensor. In addition, Relay Cards provide alarm outputs to the

field connections.

General

The power converter modules DCS800-S have the protection class IP00 and are to be mounted in a cubicle or finger protected area. 

There are different sizes (D1. D2. D3. D4. D5. D6. D7), graduated in terms of current and voltage ranges.

All units are equipped with the DCS800 Control Panel. 

It can be snapped into place on the power converter module or installed in the switchgear cubicle door by means of amounting kit. 

Accessories such as external fuses, line reactors etc. are also available, to complete the drive system. 

All converter modules up to 525 V and 1000 A (D1...D4) are equipped with field exciters.

The power section of the converters is available as single  (2-Q) bridge or double (4-Q) bridge. 4-Q drives are required for regenerative breaking. 

4-Q drives can be built by:

–Double (4-Q) armature bridge or –Single (2-Q) armature bridge plus a double (4-Q) field converter bridge

The bridge type has an influence on the maximum output voltage of the converter. See table below.

Other advantageous products on sale are listed below:

Honeywell 05704-A-0121 Four relay interface card

ABB VBS01-CJC Vert. Base Single Cold Junction Comp.

ABB VBS01-CJCA Vert. Base Single Cold Junction Comp.

ABB VBS01-EPD Vert. Base Single Ext. Pwr Inputs

ABB VBS01-EPDA Vert. Base Single Ext. Pwr Inputs

ABB VBS01-FPH Vert. Base Single Field Pwr Hot

ABB VBS01-FPHA Vert. Base Single Field Pwr Hot

ABB VBS01-FPN Vert. Base Single Field Pwr Neutral

ABB VBS01-FPNA Vert. Base Single Field Pwr Neutral

Honeywell 05701-A-0515 Front entrance 16-way splitter

Honeywell 05701-C-0390 Interconnecting Cable

Honeywell 05701-A-0365 Blanking Panel

Honeywell 05701-A-0351 Control Card

Honeywell 05701-A-0283 4 - 20mA Sensor Drive

Contact Input w/Onboard 48 V wetting 1C31142G01 1C31110G03

Digital Input (125 VAC/VDC differential) 1C31107G02 1C31110G02

Digital Input (125 VAC/VDC single ended) 1C31107G02 1C31110G01

Honeywell 05701-A-0284 Catalytic Sensor Drive

Honeywell 05701-A-0326 Field Interface Card

Honeywell 05701-A-0327 Double SPCO Relay Card

Honeywell 05701-A-0328 Triple SPCO Relay Card

Honeywell 05701-A-0329 Triple DPCO Relay Card

Honeywell 05701-A-0330 High Integrity Relay Card

Digital Input (24 VAC/VDC or 48 VDCdifferential) 1C31107G01 1C31110G02

Digital Input (24 VAC/VDC or 48 VDC singleended) 1C31107G01 1C31110G01

Digital Input (125 VAC/VDC Indiv. Fused) )1C31232G03 5X00034G01

Digital Input (125 VAC/VDC differential) 1C31232G03

Digital Input (24/48 VAC/VDC Indiv. Fused) 1C31232G02 5X00034G01

Honeywell 05704-A-0145 Control card 4-20mA

Honeywell 05704-a-0144 Four channel control card

Honeywell 05704-c-0160 Catalysis Interconnect

Honeywell 04200-A-0146 Analog output module source

Honeywell 04200-A-0145 Analog output module receiver

ABB VBX01B HN800 Bus Extender Vertical Bottom

ABB VBX01BA HN800 Bus Extender Vertical Bottom

ABB VBX01K02 HN800 Bus Extender Kit Vertical

ABB VBX01K02A HN800 Bus Extender Kit Vertical

ABB VBX01T HN800 Bus Extender Vertical Top