A-B 1746-IM16 module Rockwell SLC 16-point digital inpu

The module fits into any single slot for I/O modules in either an SLC 

500 modular system or an SLC 500 fixed system expansion chassis 

(1746-A2). It is a Class 1(1) module (uses eight input words and eight output words).

The module contains a removable terminal block providing 

connections for four thermocouple and/or analog input devices. 

There are two cold-junction compensation (CJC) sensors that 

compensate for the cold-junction at ambient temperature rather than 

at freezing 0 °C (32 °F). There are no output channels on the module. 

You configure the module with software rather than with jumpers or switches.

After completing power cycle checks, the module waits for valid

channel configuration data from your SLC ladder logic program

(channel status LED indicators are off). After channel configuration

data is transferred and channel enable bits are set for one or more

channels, the module turns on its channel status LED indicators. Then

it continuously converts the thermocouple or millivolt input to a value

within the range you selected for the channel.

Each time the module reads an input channel, the module tests that

data for a fault, for example, open-circuit, over-range, or under-range

condition. If it detects such a condition, the module sets a unique bit

in the channel status word and causes the channel status indicator to blink.

The SLC processor reads the converted thermocouple or millivolt data

from the module at the end of the program scan, or when

commanded by the ladder program. After the processor and module

determine that the data transfer was made without error, the data can be used in your ladder program.

Command Mode Operation All stepper motor operations are performed in command mode. 

This mode is entered by setting the mode flag (bit 15 in output word 0) to 0.

In command mode, the SLC Processor can issue commands and activate different operations or moves. The actions you can command are:

 • Absolute Moves

 • Relative Moves

 • Hold Moves

 • Resume Moves

 • Immediate Stop Operations

 • Homing Operations

 • Jogging Operations

 • Blend Moves

 • Preset Operations

 • Reset Errors

Diagnostic Mode

Use the configuration mode to select the diagnostic mode of operation. Once selected, 

the diagnostic mode allows you to test your program and wiring by connecting the loop back wires at the 

translator. The purpose of loop back diagnostics is to test the system wiring for electrical noise. 

The number of pulses received at the feedback should equal the commanded number of pulses at the end of the move. 

If they are not equal, the system may be experiencing problems due to electrical noise.

--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

More Model Recommendations：

1756-OB16IS module Rockwell ControlLogix 16 digital output

1756-OB32 module Rockwell ControlLogix 32 digital output

1756-OB8 module Rockwell ControlLogix 8 digital output

1756-OB8EI module Rockwell ControlLogix 8 digital output

1756-OB8I module Rockwell ControlLogix 8 digital output

1756-OC8 module Rockwell ControlLogix 8 digital output

1756-PA72 Module Rockwell ControlLogix AC Power Supply

1756-PA75 Module Rockwell ControlLogix AC Power Supply

1756-PA75R Module Rockwell ControlLogix AC Power Supply

1756-PAR2 Module Rockwell ControlLogix AC Power Supply

1756-PAXT Module Rockwell ControlLogix XT Power Supply

1756-PB72 Module Rockwell ControlLogix DC Power Supply

1756-PB75 Module Rockwell ControlLogix DC Power Supply

1756-PB75R Module Rockwell ControlLogix DC Power Supply

1756-PBR2 Module Rockwell ControlLogix Power Supply

1756-PBXT Module Rockwell ControlLogix XT Power Supply

1756-PC75 Module Rockwell ControlLogix DC Power Supply

1756-PH75 Module Rockwell ControlLogix DC Power Supply

1756-PSCA2 Module Rockwell ControlLogix Adapter

1756-OF4 module Rockwell ControlLogix 4 analog

1756-OF6CI module Rockwell ControlLogix 6 analog

1756-OF6VI module Rockwell ControlLogix 6 analog

1756-OF8 module Rockwell ControlLogix 8 analog

1756-OF8H module Rockwell ControlLogix 8 analog

1756-OG16 module Rockwell ControlLogix 16 digital output

1756-OH8I module Rockwell ControlLogix 8 digital output

1756-ON8 module Rockwell ControlLogix 8 digital output

1756-OV16E module Rockwell ControlLogix 16 digital output

1756-OV32E module Rockwell ControlLogix 32 digital output

1756-OW16I module Rockwell ControlLogix 16 digital output

1756-OX8I module Rockwell ControlLogix 8 digital output