Designed for Real-world Demands
GE Vernova’s Mark VIe control system is an integrated control system that
is widely used in a diverse range of applications including gas and steam
turbines, safety systems, wind turbines, gasification, hydro, nuclear, and
combined cycle power plants. These diverse applications require a controller
that can deliver the high performance and flexibility needed to run
application specific control reliably.
The Mark VIe UCSE is a stand-alone controller that uses QNX® Neutrino,
a real-time, multi-tasking operating system (OS), to run application-specific
control system logic.

The UCSE controller offers the following advantages:
• Single module
• No battery
• No jumper settings required
• ToolboxST programmatically updates the host application board
programmable devices
The UCSE controller mounts in a panel and communicates with I/O modules
through on-board I/O network (IONet), PROFINET, High-speed Serial Link
(HSSL), and/or other interfaces.
The available versions of the UCSE controller are: UCSEH2A for Mark VIe,
UCSEH2B for Mark VIe, LS2100e Static Starters, and EX2100e Voltage
Regulators, and UCSEH2C for EX2100e Static Exciters.
Reliable, High-Speed Performance
The UCSE Mark VIe controller is designed for high-speed, high-reliability
industrial applications. It is loaded with software specific to its application.
As a turbine or balance of plant (BoP) controller, it runs the Mark VIe
firmware and blockware applications and utilizes Mark VIe IONet interfaces.
IONet is a private special-purpose Ethernet that only supports Mark
controls I/O packs and controllers. IEEE 1588 protocol is used through
the IONet interfaces to synchronize the clock of the I/O modules and
controllers to within ±100 microseconds. External data is transferred to
and from the IO Packs the controller over the IONet Ethernet interfaces.
This includes process inputs/outputs to the I/O modules. Unlike traditional
controllers where I/O is on a backplane, the UCSE controller does not host
any application I/O. In a redundant set, all I/O networks are attached to
each controller, providing them with all input data. This hardware and
software architecture guarantees that no single point of application input
is lost if a controller is powered down for maintenance or repair.
This GMR model is designed for use in low-voltage applications and can be
used in a variety of generator types, including synchronous generators,
induction generators, and wind turbines. It is commonly used in power generation
facilities, industrial plants, and other applications where reliable generator protection
and control is critical.

The GE 469-P5-HI-A20-E-H is a type of protective relay manufactured
by General Electric (GE). Protective relays are devices that are used in
electrical power systems to detect abnormal conditions, such as
overcurrent or under/overvoltage, and to isolate the affected equipment
from the rest of the system to prevent damage or failure.
The GE 469-P5-HI-A20-E-H relay is a member of GE's Multilin 469 family
of relays, which are designed to provide comprehensive protection and
monitoring for power systems. This particular model is a high-impedance
differential relay, which means it is primarily used to protect transformers
and generators against internal faults.
The "469" in the name refers to the family of relays, the "P5" indicates
that it is a high-impedance differential relay, the "HI" refers to the
high-impedance characteristics of the relay, and the "A20" indicates that
it has 20 current inputs. The "E" indicates that it has an Enhanced Display,
and the "H" indicates that it is conformally coated.
Beckhoff CP6207-0001-0020 1.6 GHz
Beckhoff C6650-0020 industrial PC
BECKHOFF C6920-0000 MODULE
Beckhoff CP2912-0000 12.1" Touch Screen Display 2015 24VDC CP29120000
Beckhoff C6920-0050 C69200050 Celeron PCI Industrial PC
Beckhoff CX2030-0125 Basic CPU Module, TwinCAT 3. RJ45. DVI-I, 24VDC
Beckhoff CX2030-0122 Basic CPU Module, TwinCAT 2. RJ45. DVI-I, 24VDC
Mint CONDITION Beckhoff CP7802-1100-0010 touch panel
CP2915-0000 Beckhoff Multi Touch Panel 15" Touchscreen / 24VDC HMI G150XGE L04
New No Box CX1020-0110 BeckHoff CPU Module, CX1020-N010. CX1020-N000. CX1100-004
CP7203-0021-0010 , Beckhoff CP7203-0021-0010
Beckhoff CX5140-0125/4GB PLC Controller CX5140-0125/ 4GB EL1809 EL2809 EL1904
Beckhoff CP3915-0000 Multitouch Panel
EL4712 BECKHOFF 2-channel analog output module brand
BECKHOFF CX9001-1101 + CX9000-N030 + CX9000-N000 -- CX9001
| User name | Member Level | Quantity | Specification | Purchase Date |
|---|
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved