A-B 1336 PLUS II Adjustable Frequency AC Drive

With drive power ratings ranging from 0.37 kW to 448 kW (0.5 hp to 600 hp), the

Providing a single solution for virtually all your speed control requirements. The common design of the entire product line, coupled with the same control interface features, equipment

The common design of the entire product line, coupled with the same control interface features, equipment communications, training and maintenance, provides significant advantages for your control needs.

Plus, the same control interface capabilities as Allen-Bradley SMC™ and SMP™ power products, 1305 drives, 1336 IMPACT™ and 1336 FORCE™ field oriented products.

1336 IMPACT™ and 1336 FORCE™ field-oriented control drives, which all use the same control interfaces and communication options.

You'll gain significant advantages in system design, component integration, operator training, and maintenance.

Features

Protection Features

- Detection and tripping:

Undervoltage

Overvoltage

Drive overcurrent

Over temperature

External Signal

Drive Output Short Circuit

Ground fault

Loss of encoder

Temperature

Load loss

Single phase

- Overvoltage stall

- Overvoltage stall speed

- Six drive alarms

- Fault reset input

Special Functions

- Auto economiser

- Process PI controller

- Traverse function

- Optional Fault

Reset and run

- Automatic restart on switch-on

- Speed-sensitive electronics

Overload

- Auto-adjustment

- Step Logic

Operation

- Controls

- Selectable Volt/Hertz mode

- Multi-language selection

Programmable

- Dual acceleration/deceleration curves

- Three frequency jumps

- DC injection braking

- Dynamic braking

- Slip compensation

- Negative sliding compensation

Sag

- S-curve acceleration/deceleration curve

- Line Loss Restart Mode

- Active Current Limit

- Last four event fault memory

- Flight Start

- Seven preset speeds

Input/Output Interface

- Control Output Contacts

(2) Form A (N.O.)

(2) Form C (N.O. - N.C.)

Programmable to 17

Programmable to 17 different drive variables.

- Flexible analogue

Inputs/Outputs

- Pulse train input

- Encoder feedback Closed loop

Closed Loop

- High-speed inputs

Function Description

Traverse Function

The 1336 PLUS II output frequency can be programmed to modulate around a set frequency. This can be achieved by setting three parameters to create an inertia compensated delta waveform

- Traverse Period, Maximum Traverse, and P Jump. In surface drive winding applications, the developed waveforms can be used in a traverse drive to electronically perform the traverse function.

The traverse actuator will move the yarn back and forth in a diamond pattern so that the yarn is evenly distributed over the surface of the tube. This pattern must be changed in order to prevent yarn build-up at the same points on the surface. This can be achieved by constantly

continuously changing the traverse speed in a cyclic manner over a specified speed range. Using inertia compensation, a series of distributed diamond patterns can be formed over the entire surface of the tube.

Start-up operation

For applications requiring unattended operation, the 1336 PLUS II can resume operation when power is restored after a power failure.

If the Power On Run feature is activated and the input power supply is disconnected, then when the power is restored

The drive will automatically restart and run at the current commanded speed if all the necessary signals (Enable, Auxiliary, No Stop and Start) are present.

4-20mA Current Loss Option

Many control systems will issue a 4-20mA control signal for the drive to use as a speed reference.

The drive will run at the lowest speed with the 4mA signal and at the highest speed with the 20mA signal.

The drive can also invert this signal to run the minimum speed at 20mA and the maximum speed at 4mA.

Since a minimum signal of 4mA is required, the drive must have a ‘fallback’ command in the event of signal loss (sensor failure or disconnection).

The 1336 PLUS II includes a ‘Loss Selection’ parameter that provides five choices for signal failure modes.

1. stop the drive and signal a fault.

2. Go to minimum speed and issue a warning.

3. Go to maximum speed and issue a warning.

4. Maintain speed and issue a warning.

5. reaches preset speed and warns.