GE IS200ATBAG1B Application Input/Output Terminal Block

The IS200ATBAG1B is an application input/output terminal block manufactured by GE Industrial Systems for use with Innovation Series drive assemblies.

Product Description.

The IS200ATBAG1B is a terminal block assembly manufactured for the GE Innovation Series.

Part of GE's recent Innovation Series, this IS200ATBAG1B product includes a Windows 2000/XP based operator interface,

Ethernet and DCS communications and Cimplicity software. In particular, the IS200ATBAG1B has been modified by the inclusion of a single functional revision with a ‘B’ rating.

This board provides adequate backplane terminal block connections for all signals from the IS200CABP control plane assembly backplane board.

Hardware Tips and Specifications

The overall functionality of the IS200ATBAG1B Application I/O Terminal Board consists of a variety of hardware specifications. The board provides a 60-bit terminal block for all J6 and J7 jumpers connected to the CABP board.

Before purchasing the IS200ATBAG1B it should be noted that there is no customisable hardware or manually removable jumpers for this product.

While this is still true, two different versions of this IS200ATBAG1B model exist; due to different pin assignments for connector J6

as well as a different connector J7 and a different pin assignment for the corresponding connector. The J7 connector for this IS200ATBAG1B model is rated at 50V and has a maximum value of 1A.

All J6 connectors associated with this IS200ATBAG1B board are rated at 225 V and 1 a maximum current, except for the following identifiable connectors:

CONA_NO J6 connector

CONA_NC J6 connector

CONA_C J6 connector

RLY1COM connector

RLY1NC connector

RLY1NO connector

RLY2COM connector

RLY2NC Connector

RLY2NO Connector

RLY3COM Connector

RLY3NC Connector

and RLY3NO connectors

In addition to the various connectors compatible with the I/O terminal boards for this application, a specialised breakdown of the individual part numbers for this product

can reveal a lot of pertinent information about the IS200ATBAG1B hardware. Firstly, the IS200ATBAG1B begins with the ‘IS200’ series label.

This label designates the product as a General Electric product manufactured at the Salem, Virginia plant.

This ‘IS200’ designation is followed by the familiar ‘ATBA’ functional acronym, which leads to the IS200ATBAG1B group number and PCB coating type.

The ‘G1’ version of this IS200ATBAG1B product designates it as a Group 1 series product with a common PCB coating.

The total delamination coverage of the normal PCB coating is not as comprehensive as popular alternative conformal PCB coatings, but results in a thicker overall substrate protection layer.

The final noteworthy detail gleaned from the IS200ATBAG1B part number is its single-function version.

The ‘B’ digit in the IS200ATBAG1B, located at the end of the part number, indicates a single-function revision of this terminal block with a ‘B’ rating.

Frequently Asked Questions about the IS200ATBAG1B

What are the rated voltages of the various connectors for this IS200ATBAG1B model?

The connectors fixed to the IS200ATBAG1B substrate are rated for a maximum voltage of 176 V and a maximum of 1A.

Although all J6 connectors are rated at a maximum voltage of 225 a, all j& connections are rated at 50 V, maximum 1A.

What should I remember during installation or replacement of the IS200ATBAG1B board?

During replacement of the IS200ATBAG1B printed circuit board, it is recommended that it be tested before touching any circuits to ensure that lethal voltages are not present on the surface of the disconnect board before attempting to do so.

What is the difference between the G1AA and G1AB ATBA revision boards?

The difference between these two revisions of the ATBA I/O terminal boards is the reassignment of pins on connectors J6 and J7.