IBA ibaLink-SM-64-io System Interface for SIMATIC S5 and MMC

Introduction

The card ibaLink-SM-64-io is an interface board in double European size, with modified

design for SIMATIC S5 (8 bit and 16 bit) and SIMICRO MMC 216.

It is used for transmission of measured data from a SIMATIC S5 or SIMICRO MMC 216

system to an ibaPDA or ibaLogic system or for realization of a so called frame connec

tion.

The card provides a fiber optical (FO) transmitter and receiver on the front panel.

Up to 64 analog (Integer / Float) and 64 digital signals can be transmitted over these

connections.

The ibaLink-SM-64-io-card uses a dedicated memory range on the backplane bus of the

S5 or MMC system. The data to be measured are written into this memory range by the

system where the card is plugged in and are transmitted over an iba standard fiber optical

interface with 3.3 Mbit/s to the iba system.

The fiber optical receiver is used for data being sent from an ibaLogic system to the S5

or MMC system and for input of measured data from other iba systems or devices

(ibaPADU, ibaLink-MBII, ibaLink-SM-128V-i-2o etc.) to the S5 or MMC system.

By means of a crossed over point-to-point connection between two ibaLink-SM-64-io

cards or an ibaLink-SM-64-io card and another iba component with FO transmitter and

receiver in another PLC system, data can be exchanged even without an iba software

application.

Scope of delivery

 ibaLink-SM-64-io board

 S5- function blocks  (on the data medium “iba Software & Manuals”)

 P23-k1st.s5d for S5-115U (941-944) Cache Mode

 P23-k2st.s5d for S5-115U (945) Cache Mode

 P23-k3st.s5d for S5-135U (928) Cache Mode

 P23-k4st.s5d for S5-150U (924-927) Cache Mode

 P23-k5st.s5d for S5-155U (948) Cache Mode

 P23-m5st.s5d for S5-155U (948) linear addressing for multi-processor mode

System requirements

Hardware

Control system

 SIMATIC S5-155U/CPU 948. S5-150U/CPU 924-927. S5-135U/CPU 928B,

S5-115U/CPU 941B, 942B, 943B, 944B

 SIMICRO MMC 216 system with at least one free slot

Accessories

For measurement or analysis of the received data beside the board:

 PC with one of the following fiber optical interface boards:

 ibaFOB-io-S or ibaFOB-io-X, resp.

 ibaFOB-4i-S + ibaFOB-4o or

 ibaFOB-4i-X + ibaFOB-4o-X as well as

 ibaFOB-D + ibaFOB-io-ExpressCard

 also older FOB-F ISA-cards can be used

 For measuring on a notebook computer an ibaCom-PCMCIA-F card (type 2) and

the corresponding spiral cable are required.

In order to realize a frame-to-frame connection a second ibaLink-SM-64-io card or an

other iba component such as ibaLink-MBII-2io or ibaLink-SM-128V-i-2o (VMEbus) is re

quired.

Software

Accessories

For further data processing on a connected PC, the following components are required:

 Online software

 ibaPDA

 ibaQDR

 Signal manager (Soft-PLC) ibaLogic, V3.60 or higher

 ibaScope, version 3.0.01 or higher

 Analysis software

 ibaAnalyzer (V2.50 or higher)