GE Fanuc Relay output module for IC670MDL930 field control module series

DESCRIPTION: The IC670MDL930 is a field control I/O module manufactured by GE Fanuc. It is a relay output module with a total of eight (8) relay output channels consisting of six (6) sets of A-type contacts and two (2) C-type contact outputs, each installed with individual isolation. Each output contact is rated for 5VDC / 24 VDC / 125 DC voltage and 120 / 240 VAC, while the actual voltage range is 0-130 VDC, 0-265 VAC, 47-63 Hz. The module has a maximum load current of 16 amps/module.

About the IC670MDL930

The IC670MDL930 is a relay output module from GE Fanuc's field control module series. The module features individually isolated channels, specifically six (6) Type A or Normally Open (N.O.) contacts and two (2) Type C Normally Open (N.O) and Normally Closed (N.C.) contact outputs.

Each output contact is rated at 5VDC / 24 VDC / 125 DC or 120 / 240 VAC nominal, with an actual voltage range of 0-130 VDC, 0-265 VAC, 47-63 Hz, and a maximum load current of 16 A per module.The modules are available in a fixed-coil, moving-armature relay type with a maximum current draw of 313 mA.

The module has typical isolation ratings between input-to-logic, user input-to-frame ground, and group-to-group isolation, specifically, 250 VAC continuous, 1500 VAC for 1 minute.

The module has a maximum current rating of 2.0 amps for resistive loads, a voltage range of 5 to 265 VAC; 5.30 amps for 2 to 0 VDC and 31.125 amps for 0 to 2 VDC, and a maximum inrush current of 5 A for 20 ms, with a maximum load current of 10 mA per input The module has a typical response time of 10 ms to ON and OFF signal transitions, and if used with inductive loads, the response time is 10 ms per input. The module's response time to ON and OFF signal transitions is typically 10 ms, and when used with inductive loads, the maximum switching frequency is 20 cycles per minute per channel.

The module's contact outputs are made of silver alloy and have a contact resistance of 1.6 ohms at 2 A at 0 VDC. Each contact has an operating life of 20 x 10^6 operations (mechanical) and 10^5 operations (rated resistive load (electrical).

The Field Control IC670MDL930 Relay Output Module is an isolated NO/NC relay discrete output module manufactured by GE Fanuc.The IC670MDL930 Relay Output Module provides 8 isolated outputs with 6 normally open contacts and 2 normally closed and normally open contacts. These relays are also referred to as Type A relays and Type C relays, respectively. To minimise high frequency noise transients, the outputs are suppressed by RC buffers, Type A relays have normally open contacts and Type C relays have normally open or normally closed contacts. The contacts of the modules are made of silver alloy. The mechanical life of the contacts is 20 x 10^6 operations and the electrical life of the contacts is 10^5 operations.

When the IC670MDL930 Relay Isolated NO/NC Output Module has a large number of connected relay output modules, it requires more power from the BIU. The user must provide the load with an external AC or DC power supply that is driven by the contacts. Each output has an LED indicator on the logic side. The module provides fault reporting for efficient operation. It has 8-bit discrete output data that is processed for use with bus interface modules. The IC670MDL930 Relay Output Module must be supplied with the power required to energise the relay coils. The module has a maximum load current of 265 amps at 2 to 5 volts AC, 30 amps at 2 to 5 volts DC, and 31.125 amps at 0 to 2 volts DC. It has a fixed coil relay type with a moving armature. It draws a maximum current of 313 milliamps from the Bus Interface Module power supply for power-up.