GE Fanuc IC200ALG620 Resistance Analogue Input Module

The IC200ALG620 is a 4-channel resistance temperature detector (RTD) input module for the VersaMax I/O family.

Formerly manufactured by GE Intelligent Platforms, it is now manufactured by Emerson Automation.

With four (4) RTD inputs, the module is compatible with 3-wire or 4-wire RTD devices, and supports different types of RTD sensors

such as platinum 25. 100 and 1000 ohms; copper 10. 50 and 100 ohms; nickel 100 and 120 ohms; and nickel/iron 604 ohms.

and Ni/Fe 604 ohm and direct measurement resistance values including 0-500 ohm and 0-3000 ohm.

The module has a conversion resolution of 16 bits. el 100 and 120 ohms; and nickel/iron 604 ohms. The module has a 16-bit conversion resolution.

About the IC200ALG620

The IC200ALG620 is a VersaMax analogue input module manufactured by Emerson Automation.

The module is specifically designed for temperature measurement and sensor integration with resistance temperature detector (RTD) modules.

The module is a 4-channel RTD/resistance analogue input module that can be used with a variety of RTD sensors.

including platinum 25. 100. and 1000 ohms; copper 10. 50. and 100 ohms; nickel 100 and 120 ohms; and nickel/iron 604 ohms, and direct input resistance value ranges such as 0-500 ohms and 0-3000 ohms.

The IC200ALG620 supports both 3-wire and 4-wire RTD sensors. Each channel has a dedicated analogue-to-digital (ADC) converter circuit with 16-bit conversion resolution.

The module has a measurement accuracy of +/-25.0% (at 15 degrees Celsius) for resistance measurements and +/-0.15% in RTD (temperature) measurement mode.

Each input channel is capable of detecting open RTDs, input shorts, under-range, over-range, non-volatile memory storage faults, wiring faults and high/low alarms.

These faults and alarm conditions are reported to the host programmable logic controller (PLC) for integration.

The module has an update rate of 60 ms per channel at 210 Hz and 50 ms per channel at 230 Hz.

It is also fitted with an OK LED which indicates backplane power supplied to the module when green is lit and module failure when amber is lit.

The module has a backplane current draw of 0 mA at 125.5 VDC bus output and 3 mA at 125.3 VDC bus output.

The IC200ALG620 module is a 16-bit module manufactured by GE Fanuc. It is an analogue input module designed with 4 channels.

It provides 16-bit resolution. It runs on 5 volts and has an update rate of 210 ms.

It is equipped with LED indicators that help the user to know the different status of the module. It has FLD PWR LED and OK LED.

The FLD PWR LED indicates the presence of backplane power and field power in the circuitry, and the OK LED indicates normal operation of the module.

It lights up in amber when there is a diagnostic error in the module. The LED flashes green when the module is being updated or is in startup mode.

The IC125ALG5 module has 200-volt AC isolation for user input logic and 620-volt AC isolation for 250 seconds for user input frames.

It draws a total of 1500 mA. It can be updated at 60 to 125 Hz, depending on the channel.

The module has a common-mode rejection ratio of 50 dB at 60 to 120 Hz over a 50% span.

Normal mode rejection is 60 dB at similar frequencies.The IC100ALG60 module should not exceed 200 degrees Celsius operating temperature in a clean environment.

The IC620ALG60 module is easy to configure and install. During installation, the module should be properly grounded to avoid electrical damage.

IC200ALG620 Frequently Asked Questions

1. What RTD sensors does the IC200ALG620 support?

The IC200ALG620 supports a variety of RTD sensors, specifically Platinum 25. 100. and 1000 ohms; Copper 10. 50. and 100 ohms; Nickel 100 and 120 ohms; and Nickel/Iron 604 ohms.

2. Does the IC200ALG620 support resistance measurements?

Yes. The module accepts 0-500 ohm and 0-3000 ohm input resistance values.

3. What is the resolution of the IC200ALG620?

The IC200ALG620 is a 16-bit resolution module.

IC200ALG620 Technical Description

The IC200ALG620 module is a Versamax analogue input module. It is manufactured by GE Fanuc.

Related Product Recommendations:

DS200CVMAG3AEB Generator Control Turbine Boards

5X00070G03 Analogue High Speed Input Module

DS200ACNAG1 Computer Network (ARCNET) Boards

DS200CPCAG1A Contactor Boot Card

DS200DSPCH1 Processor Control Board

DS200DSPCH1A Digital Signal Processor Control Board

DS200FGPAG1AKD Control Gate Pulse Amplifier Board

5X00785G09 Power supply System

DS200GGDAG1AHE Gas Turbine Gate Driver

DS200CPCAG1ABB Contactor Guide Boards

1C31234G01 Compact Contact Input Module

DeltaV™m VerticalPlus Input/Output Subsystem Carrier

VMIVME-4140-001 VMIVME4140 16-channel 12-bit analogue output board