Power Engineering 
K-JIANG
Product
Article
NameDescriptionContent
English 简体中文
Home ⊙ NEWS ⊙ A-B 1407-CGCM Combined generator control module
Current Location:

A-B 1407-CGCM Combined generator control module

From:A-B | author:Mr.Chen | Time :2024-07-22 | 338 view: | Share:

Installation requirements

This device is intended for overvoltage applications of category II in industrial environments of pollution class 2 (as defined in IEC publication 60664-1).

The device must be mounted vertically as it contains a heat sink. Any other mounting angle will reduce the heat dissipation capability of the device and may result in premature failure of critical components.

The device can be mounted anywhere as long as the ambient temperature does not exceed the rated ambient conditions or clearance requirements.

Clearance requirements for CGCM equipment are

- 63.5 mm (2.5 inches) of clearance is required on both sides of the unit when mounted.

- 101.6 mm (4 in.) clearance is required above and below the unit when mounted.

Electrical Connections

The connection of the CGCM device depends on the application and the excitation programme. It is not possible to use all inputs or outputs in a given installation. Incorrect wiring may result in damage to the equipment.

Connect the terminals of the CGCM unit with copper wire rated at no less than 600V. General purpose wire rated for a minimum temperature of 105 °C (221 °F) may be used.

All wire must be copper. Select circuit wires according to good design practice.

The wire gauge ranges listed in the terminal block label instruction table indicate the physical capabilities of the connector.

Terminals for CGCM devices are located on the front, bottom, and right side panels of the device.

The nine-pin connector on the bottom of the unit is used for communication between CGCM devices in a redundant system. The recommended torque for the terminal screws is 1 N-m (9 lb-in).

Terminals that are used as shield wire landings are found on multiple terminal strips. Shielded terminals with the same name are connected together internally, but are not connected to a protective ground or any internal device circuit.

Excitation power supply

The excitation power supply is connected to the PMG terminals whether it is connected to the generator output (parallel excitation) or to the PMG.

The shunt excitation input is connected to the voltage transformer (VT).

The PMG inputs are located on TB1 and are labelled PMG A, PMG B and PMG C, indicating the respective phase relationship.

The single-phase excitation power supply must be connected to terminals PMG A and PMG C. The PMG inputs require twisted pair connections.

A twisted pair shielded cable is required for the PMG input.

See wiring diagram below.

Chassis Ground

The terminal marked CH GND on TB4 is the chassis ground terminal. There is also a grounding screw on the underside of the mounting flange that connects internally to the CH GND terminal.

Connect the chassis ground to the lower stud on either side of the unit with a minimum 2.6 mm2 (10 AWG) copper wire.

Connect the chassis ground to the lower stud on either side of the unit with a minimum 2.6 mm2 (10 AWG) copper wire and to the CH GND terminal with a 1.6 mm2 (14 AWG) copper wire.

When installed in a system with other CGCM devices, use a separate wire from each device to connect to the ground bus.

Analogue Inputs

The CGCM unit provides a number of analogue inputs for regulating and controlling independent or parallel generator systems. Each input is summarised below.

Generator Voltage Sense Input

The CGCM unit senses generator voltage through a voltage transformer (VT) mounted on the generator output leads.

The CGCM unit uses the voltage measured through the generator voltage sensing input for the generator voltage,

VAR and/or power factor regulation, kW and kVAR load sharing, synchronisation, metering and protection.

The input accepts signals with up to 40% total harmonic distortion (THD) and can be connected for single-phase and three-phase applications.

The generator voltage input is internally scaled by the CGCM unit according to its transformer configuration settings.

The generator voltage sense inputs are labelled V Gen A, V Gen B, V Gen C and V Gen N.

Bus Voltage Detect Inputs

The voltage measured via the bus voltage detection input is used to synchronise the generator with the bus.The CGCM device detects the bus voltage via VT.

  • Bently Nevada 2300/20-CN Monitor with 4-20ma Outputs
  • Bently Nevada 2300/20-RU 2300 Vibration Monitor
  • ABB NE810 3BSE080207R1 Network switch
  • ABB NE802 Network switch 3BSE080237R1
  • A-B 4100-234-R Compact Motion Controller
  • GE IS230TNRLH1B Relay Output DINrail Module
  • GE IS220PAICH1B Analog I/O Module
  • GE IS220PAICH1B Analog I/O Module
  • GE IS230TNAIH2C - Analog I/O DIN RAIL Module
  • ABB DAPU100 3ASC25H204 Control board I/O
  • Kongsberg RCU502I 421768 Remote Control Unit (Modular I/O Processor)
  • ABB AC 800PEC PC D237 3BHE028915R0101 / PC D237 A101 CONTROLLER BOARD
  • ABB GVC704AE01 5SHX1060H0001 3BHB003230R0101 Medium voltage inverter
  • ABB Process Panel PP245 3BSC690126R2 PP245B
  • GE Mark VIe & VIeS IS230PCAAH1B - Core Analog I/O Module
  • GE Mark VIe & VIeS IS230PCAAH1A Core Analog I/O Module
  • Emerson PMCSPANA/IH PMC Carrier Installation and Use Manual
  • Emerson PMCSPAN26E-010 Secondary PMC expansion
  • Emerson PMCSPAN26E-002 Primary PMC expansion
  • Emerson PMCSPAN16E-010 Secondary PCI expansion
  • Emerson PMCSPAN16E-002 Primary PCI expansion
  • A-B 1783-HMS4C4CGN Stratix 5400 Ethernet Managed Switches
  • A-B 1783-RA5TGC4G Stratix 4300 Remote Access Routers
  • A-B 1783-CMS10DP Stratix 5200 Ethernet Managed Switches
  • A-B 1783-CMS20DP Stratix 5200 Ethernet Managed Switches
  • A-B 1783-CMS20DP Stratix 5200 Ethernet Managed Switches
  • A-B 1783-HMS8S4CGN Stratix 5400 Ethernet Managed Switches
  • A-B 1783-CMS6B Stratix 5200 Ethernet Managed Switches
  • A-B 1783-RA5TGW Stratix 4300 Remote Access Routers
  • A-B 1783-RA2TGWC4G Stratix 4300 Remote Access Routers
  • A-B 1783-US8T/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US5TG/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-RA2TGW Stratix 4300 Remote Access Routers
  • A-B 1783-US8T/A Stratix 2000 Ethernet Unmanaged Switches—Series A
  • A-B 1783-US6T2F/A Stratix 2000 Ethernet Unmanaged Switches—Series A
  • A-B 1783-US4T1F Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US5TG Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US4T1H Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US6T2TG2H Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US5T/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US6T2TG2F Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US6T2H/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US4T1H/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US14T2S Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US6T2F Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US7T1H Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US16T2S Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-RA2TGC4G Stratix 4300 Remote Access Routers
  • A-B 1783-US16T/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US7T1F/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-RA2TGB Stratix 4300 Remote Access Routers
  • A-B 1783-LMS5 Stratix 2500 Ethernet Lightly Managed Switches
  • A-B 1783-US7T1F Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US4T1F Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US16T Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US8T Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US6T2H/A Stratix 2000 Ethernet Unmanaged Switches—Series A
  • A-B 1783-US4T1F/B Stratix 2000 Ethernet Unmanaged Switches—Series B
  • A-B 1783-US8TG2GX Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US6T2H Stratix 2000 Ethernet Unmanaged Switches
  • A-B 1783-US5T 5 Port Unmanaged Switch
  • MOOG D138-002-002 Industrial Control Module
  • MOOG D138-003-001 Industrial Control Module
  • MOOG CA98502-001 Accessories for Ruggedized Motion Controller
  • MOOG D691-078D servo valve
  • MOOG CA65866-001 MSD Motion Controller
  • MOOG C43148-001 QD10 16/16 Digital l/0 module
  • MOOG D138-002-012 Main control unit
  • MOOG CA94286-001 Accessories for Ruggedized Motion Controller
  • MOOG D136-001-008 MSCI MSD Motion Controller
  • MOOG B95906-001 MSCI Motion Controller
  • MOOG B95865-001 CAN Termination Resistors
  • MOOG QEBUS-CAN Module
  • MOOG D136-003-001 Interfaces of Ruggedized Motion Controller
  • MOOG RDI0 16/16 Digital Module
  • MOOG D136-003-004 Interfaces of Ruggedized Motion Controller
  • MOOG D391-001-003 MSD MOTION CONTROLLER
  • MOOG D138-002-003 Industrial Control Module
  • MOOG MSC-R-10 16/8 Digital and PT100 Module
  • MOOG CB08987-001 Ruggedized Motion Controller
  • MOOG RDISP 22 Operator Panel DISPLAYS
  • MOOG D136-003-002 Interfaces of Ruggedized Motion Controller
  • MOOG CA65865-001 MSCl Motion Controller
  • MOOG B95863-001 CAN Connection Cables
  • MOOG QA10 16/4 Analog Module
  • MOOG D136-006-001 EtherCAT slave interface
  • MOOG D391-001-001 MSD MOTION CONTROLLER
  • MOOG D136-003-005 Interfaces of Ruggedized Motion Controller
  • MOOG D137-004-003 TFT Touch screen display
  • MOOG D138-002-003 Industrial Control Module
  • MOOG D138-003-010 Industrial Control Module
  • MOOG CB03223-001 Accessories for Ruggedized Motion Controller
  • MOOG B95864-001 CAN Termination Resistors
  • MOOG QD10 16/16 Digital Module
  • MOOG D391-001-002 MSD MOTION CONTROLLER
  • MOOG D138-001-010 Industrial Control Module
  • MOOG D138-001-005 Industrial Control Module
  • MOOG D138-001-002 Industrial Control Module
  • MOOG D138-001-001 Industrial Control Module
  • MOOG D137-002-001 Digital I/O modules
  • MOOG QEBUS-CAN Extension module
  • MOOG D137-001-010 Connection modules
  • MOOG D137-001-004 Digital I/O modules for E-Bus
  • MOOG D137-001-007 Digital extension module
  • MOOG G391-001-001 MSD Motion Controller
  • MOOG D138-002-001 Motion Controller
  • MOOG D137-004-004 TFT Touch screen display
  • MOOG D136-002-005 Ruggedized Motion Controller Interface
  • MOOG D137-001-006 Digital extension module
  • MOOG D136-002-004 Ruggedized Motion Controller Interface
  • MOOG D137-004-006 TFT Touch screen display
  • MOOG G391-001-002 MSD Motion Controller
  • MOOG D137-004-005 TFT Touch screen display
  • MOOG D137-001-005 Digital extension module
  • MOOG D136E001-001 Programmable Processor Module
  • MOOG D138-006-001 operation panel
  • MOOG G122-829-001 Programmable Processor Module
  • MOOG G761-3002B Industrial servo valves
  • MOOG T161-902A-00-B4-2-2A Servo Controller
  • MOOG M128-010-A001B DC Power Module
  • MOOG G391-001-003 MSD Motion Controller
  • MOOG D138-002-002 Motion Controller
  • MOOG D137-001-011 Digital extension module
  • MOOG D136-002-003 Ruggedized Motion Controller Interface
  • MOOG D136-002-002 Ruggedized Motion Controller Interface
  • MOOG D136-001-008a Ruggedized Motion Controller Interface
  • MOOG D136-001-007 Ruggedized Motion Controller Interface
  • MOOG D136-001-001 Ruggedized Motion Controller Interface