Beckwith Electric M-6200A Digital Voltage Regulator Control

Digital Regulator Control for General Electric, Siemens, Cooper, Howard, 

Toshiba, TSEA, Romagnole, and ITB Regulators

• DNP+Ethernet – Send/receive DNP configuration files using DNP File

Transfer Protocol

• DNP+Ethernet – Device Discovery using TapTalk

• SCADA Heartbeat – Integrity check of communications media and/or

Master, fully programmable

• Manual Heartbeat Timer

• Quick (10‑15 sec.) Uploading of Settings, Configurations, Firmware Upgrades

• Assists in locating harmonics adversely affecting customer processes

• Helps mitigation measures to determine corrective filter design and location

• CBEMA Event Recording and Reporting

• Maximum Communication Options For Wired or Wireless Networks

• Optional single or dual Ethernet ports (copper or fiber) with simultaneous

multi‑user and multi‑protocol support

• Standard RS‑232 or RS‑485

• Optional ST or V‑Pin Serial Fiber Optic Port

• Embedded Bluetooth, Class 1 (v2.0), 1Mbps, 128 bit encryption, up to 1/2

mile transmission

• Supports DNP3.0. MODBUS and Cooper 2179 Protocols

• DNP mapping templates to match SCADA historical databases

• Time sync via DNP3.0 Set Time Command

• Sequence of Events (SOE) Recording Of Events – Stores 129 events, mSec

time‑stamped with Graphic Logic Initiate from critical operational factors

• FULL DNP implementation – Including DNP File Transfer, multi‑addressing,

unsolicited response, source address validation

• TRUE Ethernet – Full 10/100Mbps auto‑negotiable concurrent multi‑session

and multi‑protocol support

• Oscillography Capture – Selectable 16. 32. or 64 samples per cycle. Captures

sags, swells, CBEMA events and sub‑synchronous transients

• Cyber Security – Comprehensive cyber security tools to implement NERC CIP

requirements, including IPsec and Radius server security

• Data Logging Continuous Recording – Data stored in non‑volatile memory

requiring no battery backup

• Harmonics Detection, Recording, Protection and Suppression

• Downloading of Event Reports, Oscillography

• No need for battery to back up clock

• Smart Flash SD Card Slot

• Supports Control Cloning

Features

• IEEE 1686 Standard Password Compliant Cyber Security

• IPsec (Internet Protocol Security)

• RADIUS Client Capability to manage local and remote access to the control

• Adjustable Bandcenter

• Adjustable Bandwidth

• Adjustable VAr Bias

• Line Drop Compensation, R, X and Z Compensation

• Time Delay, Definite and Inverse

• InterTap Time Delay

• Four Settings Profiles

• Compare Settings Tool

• Selectable Outputs, Continuous or Pulsed

• Reverse Power Operation for Single-Phase Regulator applications

• Real-Time Metering of measured and calculated parameters

• Demand Metering with selectable time interval

• Drag Hands Operation

• Adjustable Line Overcurrent Tapchange Inhibit

• Voltage Limits

• Tap Position Limits

• Auto Runback (due to overvoltage)

• Three Independent Voltage Reduction Steps

• Sequential and Non-Sequential Operation

• SCADA Heartbeat

• Manual Heartbeat Timer

• VT Ratio Correction

• Tap Position Knowledge by Motor Direct Drive KeepTrack method

• Operations Counter

• Resettable Operations Counter

• Harmonic Analysis

• Tap Position Record

• Auto/Off/Manual Switch Status

• A or B Regulator Type Selection

• User Programmable Alarm/Deadman Contact

• SCADA Cutout (Local/Remote) switch allows blocking of write commands

from COM1. COM2 or Ethernet

• Control Voltage Input

• Source Side PT Input

• Motor Power Input

• Load Current Input

• Raise Output

• Lower Output

• 20 Character by 2 Row LED backlit LCD Display

• TapTalk S-6200 Communications Software

• USB (1.1) Communications Port

• Motor Current Profiling

• Up to 30 unique 15 character User Access Codes (Level 1 or Level 2)

• CBEMA monitoring to detect sags and swells within a range of 90 Vac to

180 Vac, and trigger data collection and alarming functions

• VAr Bias (Step and Linear Methods)

• Smart Flash SD Card Slot supports standard SD Memory Cards: SD, SDHC,

SDXC, UHS-I

• Smart Flash SD Card can be linked to one