This article summarizes the official 2017 Release 03 installation manual for **Belden‑Hirschmann GREYHOUND GRS series**, a fanless 1U 19‑inch rack‑mount managed Layer‑2 industrial Ethernet switch family. These devices target factory automation, power substation, railway track‑side, marine ship‑board and Class I Div 2 hazardous‑location applications. This summary covers hardware variants, power options, port features, LED indicators, installation workflow, safety rules, factory defaults, technical specifications and common FAQ.

1. Product Variants Overview
Four hardware models in the GREYHOUND GRS family, differing in port speed and front‑/rear‑panel layout:
| Model | Ethernet Speed | Physical Layout |
|---|---|---|
| GRS1020 | 10/100 Mbps Fast‑Ethernet | Ports front, power supply rear |
| GRS1120 | 10/100 Mbps Fast‑Ethernet | Ports rear, power supply front |
| GRS1030 | FE + Gigabit combo uplink SFP | Ports front, power supply rear |
| GRS1130 | FE + Gigabit combo uplink SFP | Ports rear, power supply front |
**Temperature grades in part‑number**:
- `S`: Standard 0 ~ +60 °C
- `T`: Extended ‑40 ~ +70 °C
- `E`: Extended with conformal coating ‑40 ~ +70 °C
**Two redundant power types**:
1. **C‑type**: 2‑pin terminal block, dual‑redundant DC 24‑48 VDC (operating range 18‑60 VDC).
2. **M‑type**: 3‑pin terminal block, dual‑redundant AC 110‑240 V / DC 110‑250 V with protective earth pin.
> Note: Two power inputs are decoupled, **no load‑sharing**. Single‑power supply triggers FAULT relay alarm, which can be disabled via switch management GUI / CLI.
2. Hardware Interfaces
2.1 Ethernet Ports
- 10/100 Mbps RJ45 copper: Auto‑negotiation, auto‑MDI‑X, max 100 m for Cat5e cable.
- **Gigabit combo ports**: RJ45 copper or SFP transceiver, inserting SFP automatically disables corresponding RJ45 port.
- Hot‑swappable media expansion module: add up to 8 extra Fast‑Ethernet ports while device stays powered‑on.
- SFP transceivers: Support multi‑mode, single‑mode, Bi‑Di, long‑haul LH optical modules. Use only Hirschmann‑qualified SFP.
2.2 Management Interfaces
1. **V.24 (RJ45 serial console)**: 9600 baud, 8‑N‑1. no flow‑control, electrically isolated from power supply, for local CLI access.
2. **USB‑A 2.0 port**: For ACA21 auto‑configuration adapter. Backup / restore config, read diagnostic logs, perform firmware upgrade. Max output 500 mA, non‑isolated.
3. **FAULT potential‑free relay contact**: Relay circuit opens when alarm events occur (power loss, link failure, ring fault). Supports remote monitoring or manual control of external hardware. For Class I Div 2 usage strictly follow entity‑parameters from drawing `000192283DNR`.
3. LED Status Indicators
LEDs are located on service panel; you can switch port‑LED output between service‑panel and port‑panel via CLI administrator commands.
| LED | Behaviour | Meaning |
|---|---|---|
| Power | Off | No valid supply voltage |
| Yellow | Only one redundant power input active | |
| Green | Both power inputs OK | |
| Blink 4‑times cycle | Firmware upgrade in progress, DO NOT remove power | |
| Status | Green solid | Device operational, ready for configuration |
| Red solid | Alarm detected, FAULT relay triggered | |
| Blink 4‑times | Duplicate IP‑address conflict | |
| RM (Ring‑Manager) | Green solid | Ring‑redundancy function healthy |
| Blink | RM configuration error | |
| Yellow | No redundant ring path | |
| ACA | Green solid | ACA21 storage adapter connected |
| Blink 3‑times | Reading / writing ACA21 media | |
| Yellow | ACA21 hardware failure | |
| Port‑Link Green | Solid | Link established |
| Blink | Port standby / port disabled | |
| Port‑Activity Yellow | Flickering | Receiving / transmitting network traffic |
> Media‑expansion module carries its own independent Power LED for module power status.
4. Safety Instructions & Certifications
4.1 General Installation Safety
1. Device rating IP20. pollution‑degree 2. for cabinet‑restricted‑access location only. Wall‑mount installation must use fire‑protected enclosure.
2. **Grounding rule**: Connect protective‑ground screw **FIRST before any other cables**. During disassembly, disconnect protective‑ground **LAST**.
3. Terminal tightening torque: power terminals 0.51 Nm; signal‑relay contact terminals 0.34 Nm.
4. Thermal requirement: Keep ventilation openings unblocked, minimum 10 cm clearance for airflow. For 19‑inch rack installation leave minimum 5 cm empty rack‑unit above device.
5. No field‑serviceable internal parts. Return faulty unit to Hirschmann‑Belden service centre.
4.2 Hazardous‑Location Class I Div 2
- Only selected certified GRS hardware variants are eligible for Class I Div 2 non‑incendive location.
- All connectors, terminal blocks **must be plugged / unplugged under power‑OFF**. Component replacement voids hazardous‑location certification.
- USB port and FAULT relay contact must comply with entity‑parameter limits from official control‑drawing 000192283DNR.
4.3 Available Certifications
- Base: CE EMC, RoHS, FCC Class A.
- Optional industry approvals: ISA 12.12.01 (Class I Div 2), IEC 61850‑3 / IEEE 1613 (power substation), EN 50121‑4 (rail‑track‑side), DNV‑GL (marine ship‑board).
- Laser safety: Class 1 laser product. Note: Class A EMC device may cause radio interference in residential environments.
5. Step‑by‑Step Installation Procedure
1. Unpack hardware and inspect for transport damage, verify delivery scope.
2. Connect protective‑ground screw first.
3. Choose mounting option:
- 19‑inch rack‑mount: Install sliding support rails (recommended for heavy‑vibration environment). Secure device brackets to cabinet.
- Wall‑mount flat‑surface: Add extra mounting brackets, deploy fire‑proof housing.
4. (Optional) Insert Hirschmann‑qualified SFP transceivers.
5. (Optional) Hot‑plug media‑expansion module, lock lever and fasten screws.
6. Wire power terminal‑blocks and FAULT‑signal relay terminals, apply specified torque. Re‑insert terminal blocks into device.
7. Power‑on unit, device runs self‑test routine.
8. Attach Ethernet copper / fiber cables. EMC best‑practice: Separate power and data cables; avoid long parallel routing, cross cables at 90‑degree angle whenever practical.
9. Fill‑in MAC‑address / IP‑address inscription‑label on front panel.
> Disassembly reverse order: Remove all data cables → cut power supply → take out terminals → remove SFP / media‑module
→ **disconnect protective‑ground lastly** → unmount hardware.
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved