GE IC698PSA350 PACSystem RX7i High Capacity Power Module

Description:

The IC698PSA350 is a power supply module for the PACSystem RX7i platform, currently part of Emerson Automation, formerly known as the General Electric Intelligent Platform (GE IP). This power supply mounts to the RX7i universal backplane. It has an input voltage range of 85 to 264 VAC 47 to 63 Hz and 100 to 150 VDC with a maximum input power of 440 watts (typical) and 500 watts (maximum). All three (3) outputs (e.g., 5 VDC, 12 VDC, and -12 VDC) have a maximum output power of 350 watts and output currents of 0-60 amps, 0-12 amps, and 0-4 amps, respectively.

The IC698PSA350 is a high capacity power supply module for the PACSystem RX7i controller family. The module is used to provide backplane power, which the module uses to activate internal circuitry and begin operation. The power supply module occupies one slot in the chassis and can only be installed in slot 0 of the RX7i chassis.

The IC698PSA350 operates with input voltages of 85 to 264 VAC, 100 to 150 VDC, and an AC input frequency of 47 to 63 Hz. The module is rated at 120/240 VAC and 125 VDC, and has input power requirements of 440 watts typical and 500 watts maximum. The power factor of this power supply module is 0.99 when used for AC input power.

The IC698PSA350 is a single-slot power supply module that mounts in the leftmost slot of the RX7i chassis or slot 0. It is equipped with various LED status indicators. It is equipped with various LED status indicators to help identify the module's operating status. These include the "Field OK", "Output OK", and "Over Temperature" LEDs. The power module has built-in protection circuits such as over-temperature and over-voltage protection and airflow protection. A 70 CFM forced air cooling fan under the system chassis provides cooling air to the power supply module. If a stoppage in airflow is detected, the overheat LED will illuminate.

The IC698PSA350 power supply is available in both Series A and Series B. The Series A power supply has an internally mounted 0.25" x 1.25" fuse, while the Series B power supply has a 5 x 20 metre fuse. The fuses installed are 8A/250V fuses.

The IC698PSA350 power supply module is part of the RX7i series and is manufactured by GE Fanuc. The module can send logic level signals to the module via the backplane. It has a rated output power of 350 watts. The rated operating voltage is 120/240 VAC and 125 VDC. The power supply module operates at 47 to 63 Hz. The operating temperature range of the module is 0 to 60 degrees Celsius. The power supply module is equipped with an airflow sensor that easily detects a fan failure or a cessation of airflow around the drive. If either of these conditions occurs, the high temperature LED will light up. The sensor can be enabled or disabled via a jumper on the outside of the module.

During installation, the GE Fanuc IC698PSA350 power module should not have any live power connections and should be properly grounded. For field wiring, the input terminals are located on the front of the module and can be connected to 120/240 VAC and 125 VDC input voltage sources. The terminals can be connected to solid or stranded wire. The ground terminal or GND should be connected to the GND terminal of the rack using 12 AWG wire. The ambient temperature of the installation area should not exceed 60 degrees Celsius during normal operation. The isolation rating of all outputs is 1500 Vdc. The IC698PSA350 module has a 15 millisecond ride-through time and a 5 millisecond hold time.

Technical Description of the IC698PSA350

The IC698PSA350 is a PACSystem RX7i power supply module formerly manufactured by GE Intelligent Platforms (GEIP) (now part of Emerson Automation). The module has an input supply voltage range of 85 to 264 VAC 47 to 63 Hz or 100 to 150 VDC, with a typical input power of 437 watts and a maximum input power of 500 watts. It has nominal output voltages of 5VDC to 60 A, 12VDC to 2 A, and - 12VDC to 1 A to the backplane. The module output power is 350 watts.

Related Product Recommendations:

5X00419G01 Ethernet Link Controller