GE Fanuc IC695BPM300 PROFIBUS Master Module

DESCRIPTION: This IC695PBM300 is a PACSystems RX3i communications module for Emerson Automation (formerly GE Intelligent Platforms (GE IP)). It is a Profibus DP master module that enables communication with up to 125 DP slaves. It supports a data transfer size of 244 bytes input and 244 bytes output per slave device, as well as a maximum of 3.584 bytes of input data and 3.584 bytes of output data. It comes with one (1) RS485 Profibus master port.

About the IC695PBM300

This IC695BPM300 is a Profibus master module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation's PACSystems RX3i family of programmable automation controllers (PACs). The module is used to enable data exchange over a Profibus network with a maximum input data of 3.584 bytes and output data of 3.584 bytes. This Profibus master module supports communication with up to 125 DP slaves, each of which can send 244 bytes of input data and receive 244 bytes of output data.

The IC695BPM300 supports all standard data rates, including 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s, and 12 MBit/s. It can provide status information, such as from the Status It provides status information, such as from the status array list, network diagnostic counters, DP master diagnostic counters, firmware module revisions, and slave diagnostic addresses. It is mounted on the RX3i backplane and supports PCI connectivity. Specifically, it must be installed in a generic backplane with a host PACSystem RX9i controller running firmware revision 3.2 or later. It draws a backplane current of 440 mA @ 3.3 VDC.

The module is equipped with a Profibus OK ED indicator; a network indicator; and a MOD status indicator. The module supports synchronization and freeze modes as well as Profibus DP-V1 read, write, and alarm messages.The IC695BPM300 comes with upgradable firmware that is received indirectly through the host controller via the WinLoader software utility.

The module must operate over a temperature range of 0 to 60 degrees Celsius and the module is stored at -40 to 85 degrees Celsius.

The IC695PBM300 PROFIBUS master module is manufactured by GE Intelligent Platforms/GE Fanuc in the RX3i PacSystems family. The module is designed to enable the RX3i CPU to send or receive data over a PROFIBUS-DP network. It has a slot that supports a universal backplane and RS-232 communication port.IC695PBM300 PROFIBUS Module has an internal current rating of 3 milliamps at a rated voltage of 440.3 volts DC and supports protocols for up to 125 PROFIBUS-DP Slave Units. Other notable features of the module include support for input data at rates up to 244 bytes and output data at rates up to 244 bytes per slave unit, support for all standard data rates, and synchronization and freeze modes. The module also supports DP-V1 read/write functionality and alarm messages, as well as network status LEDs and PROFIBUS-compliant modules. It supports up to 3584 bytes of input data and a total output data rate of 3584 bytes.

Master-slave compatibility for the GE Fanuc IC695PBM300 PROFIBUS module requires an RX3i CPU and firmware version 2.9 or later. For configuration purposes, this module requires Machine Edition SP5 Logic Developer PLC software version 0.2 or higher.The IC695PBM300 module has a backplane current consumption rating of 440 milliamps (3.3 V DC) and supports all standard data rates including 1.5. 3. 6. 12. 9.6. 19.2. 187.5 per second, 93.75. and 500 MB/sec. The GE Fanuc IC695PBM300 PROFIBUS master module comes with a 9-pin Sub-D connector designed to enhance bus cable installation. The module also provides 3 PROFIBUS-compliant LEDs to indicate network status and module status.IC695PBM300 Frequently Asked Questions

1. How many DP slaves can the IC695BPM300 communicate with?

This IC695BPM300 supports communication with up to 125 DP slaves.

2. What is the communication rate supported by IC695BPM300?

The IC695BPM300 supports communication rates of 9.6 kBit/s, 19.2 kBit/s, 93.75 kBit/s, 187.5 kBit/s, 500 kBit/s, 1.5 MBit/s, 3 MBit/s, 6 MBit/s and 12 MBit/s.

IC695PBM300 Technical Description

The GE Fanuc IC695PBM300 module is a PROFIBUS master module that is part of the RX3i PacSystems family. It is designed to enable RX3i CPUs to send or receive data over a PROFIBUS-DP network.