GE IC695ALG628 PACSystem RX3i Non-Isolated Analog Input Module

DESCRIPTION: The IC695ALG628 is an analog input module that is part of the PACSystem RX3i platform, which is currently part of Emerson Automation and was formerly manufactured by GE Intelligent Platforms (GE IP). The module features eight (8) non-isolated single-ended input channels or four (4) differential input channels supporting +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC, and 0-20 mA, 4-20 mA, and +/- 20mA input signals. The module has a built-in ADC converter that converts data to floating point data type integers with 24-bit resolution. The module supports High Speed Addressable Remote Sensor (HART) version 5.0.

About the IC695ALG628

The IC695ALG628 is an analog input module with High Speed Addressable Remote Sensor (HART) 5.0 functionality. This module is part of the mid-range controller family, the PACSystem Rx3i series with eight (8) analog input channels (configured as single-ended) and four (4) input channels (if used in a differential distribution line configuration). It comes with two (2) internal HART modems. The module's parameters and configuration are completely software configurable and each channel can be individually assigned high alarm, low alarm, high high alarm, low low alarm detection and reporting to the CPU. In addition, positive and negative rate of change alarms and configurable interrupts for channel alarms and faults can be set accordingly. The module also comes with upgradable firmware and performs an automatic calibration each time the module is powered up.

The module's analog input channels are designed to accept +/-10 VDC, 0-10 VDC, +/- 5 VDC, 0-5 VDC, 1-5 VDC and 0-20 mA, 4-20 mA and +/- 20mA input signals. It has built-in analog-to-digital (ADC) converter circuitry that converts received analog data to 24-bit registers or 32-bit integers in floating point. Each module channel has a variety of filter options, often used to eliminate signal fluctuations for more stable readings.

The module's power consumption is 450 mA maximum @ 5.0V +5%/-2.5% and 625 mA maximum @ 3.3V +5%/-3%. It incorporates continuous maximum overcurrent protection rated at +/-28mA and continuous maximum overvoltage protection at +/-60 VDC. The module has an open-circuit detection time of up to 1 second.

GE Fanuc IC695ALG628 Non-Isolated Differential Analog Input Module with HART (High Speed Addressable Remote Transducer) Communication for RX3i PacSystem PLCs provides 4 differential input channels and 8 single-ended input channels. It has 2 internal HART modems and features HART version 5.0 HART communications on each channel. It has a voltage range of 1 to 5 volts DC, 0 to 5 volts DC, +/-5 volts DC, 0 to 10 volts DC, or +/-10 volts DC. The current configuration of the input channel can range from +/-20 mA, 0 to 20 mA, or 4 to 20 mA. The GE Fanuc IC695ALG628 analog input module should be configured for a current range between 4 and 20 mA when the channel is connected to a highway addressable remote sensor communication system.

The GE Fanuc IC695ALG628 Analog Input Module supports the use of extension box IC694TBB132 block, box IC694TBB032 block, extension spring IC694TBS132 block, and spring IC694TBS032 block terminal blocks. Extension terminals are installed to provide the extra shroud depth required for shielded wiring. Terminals are usually purchased separately. The analog input module has internal power supplies of 3.3 V (600 mA) and 5 V (450 mA). It has flash memory for future upgrades, error reporting, rate-of-change alarms, software that can be configured without setting jumpers, terminal insertion or removal detection, and complete auto-calibration. The module requires a non-condensing ambient humidity range of 5% to 95%.The GE Fanuc IC695ALG628 module is mounted in the general purpose backplane of the RX3i PacSystem PLC.

IC695ALG628 Frequently Asked Questions

1. Does the IC695ALG628 detect incorrectly installed terminals?

Yes. The module monitors the terminal connections with the appropriate LEDs.

2. Does the module support the HART protocol?

Yes, the module supports the HART 5.0 protocol. The module supports the HART 5.0 protocol.