GE Fanuc IC695ALG600 Resistance Temperature Detector (RTD) Input Module

This IC695ALG600 is a general-purpose analogue input module for the PACSystems RX3i programmable automation controller (PAC) platform.

The module supports a wide range of input signals such as voltage, current, resistance, and supports thermocouples and resistance temperature detectors (RTDs).

The module is now manufactured by Emerson Automation, formerly known as GE Intelligent Platform (GE IP).

This IC695ALG600 comes with two (2) banks of four (4) channels each that can be configured for any combination of input signals.

It supports 0-20 mA, 4-20 mA, +/-20 mA current signals; +50 mV, +150 mV, 0-5 V, 1-5 V, 0-10 V, +10 V voltage signals.

0 to 250 / 500 / 1000 / 2000 / 3000 / 4000 ohm resistance signals; PT 385 / 3916. N 618 / 672. NiFe 518. CU 426 RTD sensors.

B, C, E, J, K, N, R, S, T thermocouple inputs.

The IC695ALG600 is installed on the RX3i Universal Backplane and requires at least firmware version 2.80 or higher.

This module is configured using Proficy Machine Edition (PME) version 5.0 SP1A LD-PLC Hotfix 1 or higher.

For signal termination, this module requires a cassette (IC694TBB032), expansion cassette (IC694TBB132),

spring-loaded (IC694TBS032) or extended spring-loaded (IC694TBS132) terminal blocks. Extension terminals are recommended.

These terminals have slightly larger covers to accommodate wires and shields with thicker insulation.

The module supports flash memory and status LEDs for future upgrades, such as module status, field status, and TB LEDs.

The GE Fanuc IC695ALG600 Resistance Temperature Detector (RTD) Input Module has a maximum power consumption of 5.4 watts.

The internal power rating is 350.3 mA at 350.3 volts and 5 mA at 400 volts.400. The input channels are divided into 2 groups of 4 each.

Each channel can be independently set up using Machine Edition software to operate at +/-50 mV, +/-150 mV, 0 to 5 volts, 1 to 5 volts, 0 to 10 volts, 1 to 5 volts, and 0 to 10 volts,

1 to 5 volts, 0 to 10 volts DC, +/-10 volts DC, or 0 to 20 mA, 4 to 20 mA, or +/-20 mA.

Thermocouple input types include types B, C, E, J, K, N, R, S, or T. Resistance inputs are rated from 0 to 250. 500.

1000. 2000. 3000. or 4000 ohms, and 8 channels that can be voltage, resistance inputs, thermocouple, and current inputs.

The GE Fanuc IC695ALG600 RTD input module has configurable input filters.

The possible frequencies are as follows: 8 Hz, 12 Hz, 16 Hz, 40 Hz, 200 Hz, or 1000 Hz.

It also has a maximum RTD cable impedance rating of 25 ohms. This module is located in the RX3i general purpose backplane and cannot be located in a remote or expansion backplane.

It has a Module Normal LED that indicates the status of the module. The Field Status LED indicates a fault on the smallest channel or an error on a terminal.

The Terminal LED indicates the presence of a terminal. the IC695ALG600 module has an operating temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit).

The IC695ALG600 module has an operating temperature range of 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit) and a storage temperature range of -40 to 85 degrees Celsius (-40 to 185 degrees Fahrenheit).

IC695ALG600 Frequently Asked Questions

1. What input signals and sensors does the IC695ALG600 support?

This IC695ALG600 supports 0-20 mA, 4-20 mA, +/-20 mA current signals; +50 mV, +150 mV, 0-5 V,

1-5 V, 0-10 V, +10 V voltage signals; 0 to 250 / 500 / 1000 / 2000 / 3000 / 4000 ohm resistance signals.

PT 385 / 3916. N 618 / 672. NiFe 518. CU 426 RTD sensors; B, C, E, J, K, N, R, S, T thermocouple inputs.

2. Does the IC695ALG600 come with input grouping?

Yes. The module has two (2) groups of four (4) inputs each.

IC695ALG600 Technical Description

The GE Fanuc IC600ALG3 module for the RX695i PacSystems family is a resistance temperature detector (RTD) input module.

It provides two cold-junction compensation (CJC) channels and eight general-purpose input channels.