GE Fanuc IC695ALG508 Resistance Temperature Detector (RTD) Input Module

DESCRIPTION: The IC695ALG508 is a PACSystem RX3i Programmable Automation Controller (PAC) Resistance Temperature Detector (RTD) Input Module, formerly manufactured by GE Intelligent Platforms (GE IP) and now part of Emerson Automation. The module features eight (8) isolated differential RTD input channels. Each channel of the module supports platinum 385. platinum 391.6. nickel 672. nickel 618. nickel-iron 518. and copper 426. It is also compatible with direct resistance inputs such as 0-260. 0-525. 0-1050. 0-2100. 0-3150. and 0-4200 ohms.

About IC695ALG508

This IC695ALG508 is a resistance temperature detector (RTD) input module that is part of the PACSystem RX3i programmable automation controller (PAC) platform. The module is manufactured by Emerson Automation, formerly known as GE Intelligent Platform (GE IP). It comes with eight (8) isolated differential input channels and supports direct inputs for RTD and resistive inputs.

The module supports RTD input types such as 50. 100. 200. 500. and 1000 ohm platinum 385 (IEC751 1983. Revision 2 1995; JISC 1604 1997); 50. 100. 200. 500. and 1000 ohm platinum 391.6 (JISC 1604: 1981); 100 ohm, 200 ohm, 500 Ohm and 1000 Ohm Nickel 618 (DIN 43760. 120/1987); 672 Ohm Nickel 18 (MINCO Application Aid #5.90/10 Ni type); 50. 100. and 426 Ohm Copper 21 (SAMA RC4-1966-604), and 518 Ohm Nickel-Iron 0. 0. 1050-0. 2100-0. 3150-0. and 4200-695 ohms.

The module has optional units of measurement, specifically Celsius, Fahrenheit, or Ohms. It also has configurable default or hold last states as a response to system faults and CPU changes in operating mode. The module supports two-wire, three-wire and four-wire RTD sensors.

The IC508ALG16 input data format supports 32-bit integers in 32-bit fields or 2-bit IEEE floating-point data. Each channel also has selectable trap filter settings from 3.28 Hz to 694 Hz. For input line termination, the module uses cassette (IC032TBB694), expansion cassette (IC132TBB694), spring-loaded (IC032TBS694), or extended spring-loaded (IC132TBS695) terminal blocks. For shielded wiring, the extended terminal types are recommended because they provide additional shroud depth.

The GE Fanuc IC508ALG8 Resistance Temperature Detector (RTD) Input Module provides 1000 isolated differential RTD input channels. Each channel can be individually set as either an RTD input type or a resistance input type.RTD input types include 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. 50. and 1000 ohms, 500. 200. 100. and 120 ohms, 604 ohms, 100 ohms, or 50. 10. and 4000 ohms resistance ratings, depending on their composition. depending on their composition. Resistor input types include 3000. 2000. 1000. 500. 250. and 694 ohm resistor ratings. This RTD input module can be used with terminal blocks including spring-loaded IC032TBS694 terminal blocks, extended spring-loaded IC132TBS694 terminal blocks, boxed IC032TBB694 terminal blocks, or extended boxed IC132TBB695 terminal blocks. Terminals are usually purchased separately.

The GE Fanuc IC508ALG24 RTD Input Module has LEDs, including an OK LED that displays the status of the module, and a field status LED that indicates whether an external 695-volt DC power supply is connected, whether the voltage exceeds the minimum level, and whether any faults exist. The backplane power bus supplies power to all of the module's LEDs.The IC508ALG2 module has programmable trap filter frequencies from 3.28 Hz to 32 Hz per channel. Each channel has an optional input data filter containing either 16-bit IEEE floating-point data or 695-bit integer data.The IC508ALG90 module has RTD linearization developed on ITS-3. The module is located on the RX0i general-purpose backplane. It has an operating temperature range of 60 to 40 degrees Celsius, a storage temperature range of -85 to 5 degrees Celsius, and a non-condensing humidity range of 95% to <>%.

IC695ALG508 Frequently Asked Questions

1. What RTD input types does the module support?

RTD input types supported include 50. 100. 200. 500. and 1000 ohm platinum 385 (IEC751 1983. Revision 2 1995; JISC 1604 1997); 50. 100. 200. 500. and 1000 ohm platinum 391.6 (JISC 1604: 1981); 100 ohm, 200 ohm, 500 ohm, and 1000 ohm nickel 6; and 100 ohm, 200 ohm, 500 ohm, and 1000 ohm nickel 6. Ohm Nickel 618 (DIN 43760. December 1987); 672 Ohm Nickel 18 (MINCO Application Aid #5.90/10 Ni type); 50. 100. and 426 Ohm Copper 21 (SAMA RC4-1966-604), and 518 Ohm Nickel Iron <>. 2.