GE Fanuc IC200ALG266 15-Point Analogue Current Input Module

The IC200ALG266 is a 15-point analogue current input module for the VersaMax I/O family, formerly manufactured by GE Intelligent Platforms and now manufactured by Emerson Automation.

The module features fifteen (15) single-ended input channels that accept -10 to +10 VDC input signals with 15-bit resolution** and an update rate of 7.5 ms.

The module has a **backplane current consumption of 150 mA.

About the IC200ALG266

The IC200ALG266 is a VersaMax analogue input module. The module is intended for use in distributed I/O architectures.

It is used to connect analogue measuring instruments and feedback devices to generate a signal voltage range of 10 VDC to + 10 VDC.

The input module has an analogue-to-digital signal conversion resolution of 15 bits or 0.3125mV per count.

The IC200ALG266 is powered by a backplane power supply** with a current consumption of 150 mA. it does not require an external power supply to activate each input channel.

It does not require an external power supply to activate each input channel, as the embedded fifteen (15) analogue input channels support a current sink wiring configuration.

The module has a full-scale accuracy of +/-3.0% at 0 degrees Celsius operating temperature,** a full-scale accuracy of +/-5.25%, and a full-scale** value of +/-60% at 1 degree Celsius.

Each channel of the IC200ALG266 is capable of detecting faults in analogue signal conversion.

This occurs when the output provided by the AD converter is greater than 6% of the full scale value.

This error is reported to the CPU, which can indicate to the partner Human Machine Interface (HMI) and Supervisory Control and Data Acquisition (SCADA) systems as a fault or poor signal quality.

The IC200ALG266 has software configurable input states in response to a CPU stop or module error.

These options include default or *last state operation and are suitable for achieving safe startup, especially in the event of a power interruption.

Filter response is 32 Hz +/-20% per input channel with a channel update rate of 7.5 ms.

The GE Fanuc Automation IC200ALG266 module is a certified Versamax input module manufactured by GE Fanuc Automation.

The module is designed to provide an interface to different input devices. The interface is achieved by connecting to the 15 input channels included in the module.

These inputs are analogue and the module comes with an LED that indicates when the drive is correctly configured and able to operate, this LED is the OK LED.

The GE Fanuc Automation IC200ALG266 Versamax Input Module has protection features that ensure safe operation and help extend the life of the module and inputs.

These protection features protect the module from overvoltage levels above 30 volts DC.

The operation of each input is a separate operation, which means that if one is in a fault condition, it will not affect the function of the remaining inputs.

The GE Fanuc Automation IC200ALG266 Versamax input module has a backplane current consumption rating of 50 mA to 100 mA.

It cannot be run from an external power supply.The IC200ALG266 Versamax input module has a 15-bit resolution.

However, it may need to be derated by up to +/-2% if it is subject to RF interference. The module filters at a channel update rate of 7.5 milliseconds.

The input current range of the module is -10 VD to +10 VDC.

IC200ALG266 Frequently Asked Questions

1. Does the IC200ALG266 support installation into distributed I/O stations?

Yes. The IC200ALG266 can be used as local or remote I/O.

2. Does the IC200ALG266 support 4-20 mA signals?

No. Only -10 to 10 VDC signals are supported. Only -10 to 10 VDC signals are supported. 3.

3. Does the IC200ALG266 have separate isolated input channels?

No. The IC200ALG266 has only one set of 15 input channels. 4.

4. Can the IC200ALG266 detect internal power loss?

Yes, the IC200ALG266 can detect internal power loss and AD converter circuit faults.

IC200ALG266 Technical Description

The IC200ALG266 is a Versamax I/O module. The module is manufactured by Emerson Automation, formerly known as GE Fanuc.

It is a 15-channel, single-ended analogue input module with 15-bit resolution. It accepts (-) 10 VDC to (+) 10 VDC voltage input signals.