Eaton Protection Features EDR-5000

Features

Protection Features

• Phase overcurrent elements:

• Three instantaneous elements with timers ( 50P[1], 50P[2], and

50P[3])

• Three inverse time overcurrent elements (51P[1], 51P[2], and

51P[3])

• 11 standard curves

• Instantaneous or time delay reset

• Voltage Restraint (51P[2], and 51P[3])

• Directional Control (All Elements)

• Ground overcurrent elements:

• Two instantaneous measured elements with timers (50X[1],

and 50X[2])

• Two instantaneous calculated elements with timers (50R[1],

and 50R[2])

• Two inverse time overcurrent measured elements (51X[1], and

51X[2])

• Two inverse time overcurrent calculated elements (51R[1], and

51R[2])

• 11 standard curves

• Instantaneous or time delay reset

• Directional Control (All Elements)

• Breaker failure (50BF) .

• Phase unbalance negative sequence overcurrent (46[1], 46[2])) .

• Phase voltage unbalance and sequence protection (47[1], 47[2]) .

• Main 3-phase under/overvoltage (27M[1], 27M[2], 59M[1], 59M[2])

• Auxiliary single-phase under/overvoltage (27A[1], 27A[2], 59A[1],

59A[2])

• Ground fault overvoltage relay (59N[1], 59N[2])

• 6 Frequency elements that can be assigned to: over frequency,

under frequency, rate of change, or vector surge (81[1], 81[2],

81[3], 81[4], 81[5], 81[6])

• Apparent and displacement power factor (55A[1], 55A[2], 55D[1],

55D[2]) .

• Forward and Reverse Watts (32[1], 32[2], 32[3])

• Forward and Reverse Vars (32V[1], 32V[2], 32V[3])

• Synch Check (25)

• Autoreclosing (79)

• Zone interlocking for bus protection (87B) .

• Switch onto fault protection

• Cold load pickup

Metering Features

• Amperes: Positive, negative and zero sequence .

• Ampere demand .

• Volts: Positive, negative and zero sequence .

• Phase angles .

• Volt-amperes and VA demand .

• Watts and kW demand .

• kWh (forward, reverse, net)

• Vars and kvar demand

• kvarh (lead, leg and net) .

• Power factor .

• Frequency .

• % THD V and I .

• Magnitude THD V and I

• Minimum/maximum recording .

• Sync Values

• Trending (load profile over time)

Monitoring Features

• Trip coil monitor

• Breaker wear primary and secondary (accumulated interrupted

current) .

• Oscillography (6000 cycles total) .

• Fault data logs (up to 20 events) .

• Sequence of events report (up to 300 events) .

• Clock (1 ms time stamping) .

Control Functions

• Breaker open/close

• Remote open/close

• Programmable I/O

• Programmable Logic

• Programmable LEDs

• Multiple setting groups .

• Cold load pickup .

• CT supervision

Communication Features

• Local HMI .

• Password protected .

• Addressable .

• IRIG-B

• Local USB communication port .

• Configuration software

• Remote communication port:

• RS-485 Terminals

• Ethernet RJ45

• Fiber Optic ST

• RS-485 D-SUB

• LC Duplex Fiber Optic

• Protocols:

• Modbus-RTU

• Modbus-TCP

• IEC-61850

• DNP3-RTU

• DNP3-TCP/UDP

• Profibus-DP