Distributed Processing Unit Functionality
The Model PDP Distributed Processing Unit (DPU), which runs under the
Windows CE.net real-time multitasking operating system, is the hardware
processing engine of the maxDNA distributed control system. The DPU
performs primary data acquisition, control, and data processing functions.
The DPU, also known as maxDPU4F, is a self-contained microprocessor
based, rack-mounted unit, which occupies a single slot in a Remote
Processing Unit cabinet using an 8-wide maxPAC backplane. It is designed
to operate with user-defined combinations of maxDNA Model IOP
Input/Output Modules, and to communicate with other devices, such as
Programmable Logic Controllers and Remote Terminal Units.

As a station on maxNET, the DPU scans and processes information for use
by other devices in the maxDNA system. Each DPU performs:
• Comprehensive alarming and calculations.
• Logging of Sequence of Events (SOE) data at 1 millisecond resolution.
• Acquisition of trend information.
• Continuous scanning of Model IOP I/O modules.
• Execution of predefined algorithms, called Function Blocks, for process
control and data acquisition.
Model Numbers
Model PDP401 – DPU4F #181550
Model PDP403 – DPU4F #181550. Backup Cable #050292
Model PDP406 – DPU4F w/IRIG & Comm. #181551
Model PDP408 – DPU4F w/IRIG & Comm #181551. Backup Cable
#050292
Distributed Processing Unit Hardware
A DPU consists of a printed circuit board containing the Control Processor
and Input/Output Processor (IOP) and is installed in a maxPAC chassis. The
DPU’s front panel contains status LEDs, a MODE Switch, Backup
Connector, Network Connectors, and takeover and reset buttons. An
optional assembly also contains a Serial Port Connector for interface to PLCs
and a BNC Connector for interface to an IRIG-B time source. See "Front
Panel Controls and Features," later in this chapter.
Control Processor
The DPU is comprised of a single printed circuit board that contains a
Pentium class Control Processor and a dedicated micro-controller for
scanning I/O. There are also sockets on the board for 64 Mbytes of
CompactFlash and 128 Mbytes of DRAM.
Performance
A multi-speed processing system is built into the maxDPU4F, which allows
objects to be executed in three different time classes. From as fast as 10 msec
to 1/2 second. Up to 8.500 control objects (Function Blocks)can be executed
in the DPU. Note also that Function Blocks can be combined to create
libraries of Standard and Custom Blocks. A Function Block can be as small
as an Atomic Block, such as an AND or OR gate.
A data point management system (DPMS) keeps track of the object size and
the total execution time for each time class.
I/O Bus Interface
A Motorola 68332 32-bit I/O processor and field programmable gate array
(FPGA) are used to interface to both the Model IOP I/O bus and to the I/O
Bus Expander Module (BEM) for remote I/O applications. Up to 60 Model
IOP I/O modules can reside on each electrical bus. See Publication 278596.
maxPAC Hardware Reference Guide, and for earlier Model 564 I/O, see
278563. Model IOP I/O System Installation and Preparation. The maximum
length of the Model 564 I/O bus is 30 ft. The length of the remote I/O link
with fiber optic extenders is up to 2000 m.
Fully Self Describing Object Oriented Database
All information regarding the operation of the DPU is kept in DPU memory,
including: tag names, descriptions, tuning constants, alarm limits, etc. In
addition, all graphical configuration data (sheet number, object location,
wiring) is stored in the DPU.
This means that there is no possibility that the configuration observed is
different than that which is installed in the DPU.
Objects are stored in a fully hierarchical database, allowing for easy cut and
paste changes and protection of control strategies.
Fully Software Backplane Compliant
With the software backplane installed, the DPU can access any exposed data
stored anywhere in a connected system as long as the connected system also
uses the SPB Protocol. Peer-to-peer transfers are rapid and transparent. No
independent transfer agent is required.
The Software Backplane uses subscription services where data is only
transmitted when changes are detected.
Sequence of Events
Each DPU includes a built-in Sequence-of-Events (SOE) recorder that can
monitor up to 512 discrete inputs. These inputs are scanned 1.000 times a
second and state changes are time stamped with 1 ms resolution and stored in
the DPU's 10.000-event buffer. Each input has a separately configurable
digital filter for contact debounce.
Distributed Processing Unit Specifications
Operating temperature range
Storage temperature range
Relative humidity range
Power requirements
Current:
Powering the DPU
0 to 60 degrees C
(-)25 to 70 degrees C
5 to 90% noncondensing
24 Vdc ±4 Vdc
0.9 A @ 24 Vdc
The DPU operates from the main redundant 24 Vdc power supply system in
the maxDNA system cabinets.
Mounting the DPU
The DPU is mounted on the Input/Output (I/O) backplane with maxPAC and
earlier Model 564 Input/Output modules.
Positioning the DPU in a Standard maxPAC Chassis
The DPU must be mounted in the left most position of the Model IOP rack to
allow for the best airflow. The Backup cable and Ethernet communications
cables should be laced to the left side of the chassis with at least a 1 inch
bend radius to allow for easy removal of the DPU, while limiting the strain
on the RJ45 connectors.
When using a second DPU for backup, it should be mounted vertically
beneath the primary DPU for ease of connection of the two-foot backup
cable. The cable is to be held in place by tying to the cable hold downs on
the side of the IOP rack.
The DPU is designed to allow installation and removal with the +24 V dc
power supply turned on.
Positioning the DPU When Upgrading
The DPU can be mounted on the right side of a Six Wide maxPAC chassis or
any slot of the Four Wide Model 564 chassis. In either case, remove all
mounting hardware and termination panels that supported the earlier model
DPU. Install a Chassis 4 Wide maxPAC adapter (Metso Automation
#047350) in the cleared space using the two mounting holes located in the
back panel metal frame.
If the previous DPU was a DPU4E, the Ethernet cables that were plugged
into the termination panel can be plugged directly into the front panel of the
DPU card. Make sure that the settings of the Ethernet switch match the setup
file. See Chapter 5 for the configuration setup.
If the previous DPU was a DPU3. DPU4A, or DPU4B; new Ethernet
switches and cables will need to be installed. Consult the factory for details
about this type of upgrade.
In all upgrade situations, the backup cable must be replaced with a DPU4F
backup cable (Metso Automation # 050292).
Mounting Procedures
Before mounting any hardware, refer to the cabling and field wiring sections
of Publication 278596. maxPAC Hardware Reference Guide, and Publication
278563. Model IOP Input/Output System Installation and Preparation.
To install the DPU in the rack, refer to Chapter 7 Starting the DPU.
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved