Power Engineering 
K-JIANG
Product
Article
NameDescriptionContent
English 简体中文
Home ⊙ NEWS ⊙ Horner CPU300 and HMI Connect Series Mounting Overview
Current Location:

Horner CPU300 and HMI Connect Series Mounting Overview

From:Horner | author:Mr.Chen | Time :2025-09-12 | 221 view: | Share:

Mounting Overview

The mechanical installation greatly affects the operation,safety,and appearance of the system.

Information is provided to mechanically install the unit such as cut-out sizes,

mounting procedures,and other recommendation sfor the correct mechanical installation of the unit.

Requirements

l Each module is compact and mounts on the DIN rail. Each I/O module installed adds 

width in increments of 19mm.The distance between wiring duct and surrounding

modules must be at least 50mm apart.

l The DIN rail clip adds to the overall measurements.The CAN,power,LAN,and serial connectors also add to the

measurements.

l Modules can be added after the base has been installed on the DIN rail and can be hot swapped with power

applied.

NOTE: I/O scanning will stop until the correct modules for the system are detected in all slots.

Din Rail Alignment Requirements

1. Confirm that the DIN rail is in a horizontal position before installing the unit.

Horizontal orientation is required to avoid module slippage on the DIN rail.

2. Align the unit on the DIN rail then push the DIN rail clip to until it clicks in to place.

Check to ensure that the unitis secure on the DIN rail.

Mounting Orientation

NOTE: Do NOT mount the unit on its side as this may cause the unit from slipping off the DIN rail.

l Mount the CPU300 with the locking DIN tab facing down.

l As modules mount on a DIN rail, be certain that the DIN rail is in a horizontal position before installing the unit. 

A horizontal orientation is required to prevent the unit from slipping off the DIN rail.

Module Removal

Modules maybe removed while powered;however,I/O scanning on the remaining modules will stop

and I/O will go into  the default state until a new module is inserted and all modules in the configuration are present.

1.Insert a flat-blade screwdriver into the DIN rail latch at the bottom of the module.

2.Pry down wards on the release latch.

3.Rock the module up and off the DIN Rail.

  • Eaton F30 Ex ic Adaptor ATEX & IECEx Approved
  • ABB DRIVEMONITOR VERSION 4000 DRIVE MODULE RBOX316-ABB-00
  • ABB VACUUM CONTACTOR VSC7 SCO IEC 60470 400A 3POLE 220-250V 50/60Hz
  • Johnson Controls MS-NAE5512-1 Supports two N2 or two BACnet MS/TP (RS-485) trunks
  • Johnson Controls MS-NAETUNL-8 ToggleTunnel utility for converting an NAE55/NIE55 to an NAE55 model
  • Johnson Controls MS-MECVT-0 MS/TP to Ethernet Converter
  • Johnson Controls MS-SECVT-0 Serial to Ethernet Converter
  • Johnson Controls AS-XFR100-1 Power transformer
  • Johnson Controls AS-XFR100-1 Power transformer
  • Johnson Controls MS-FEC2621-0U FEC26 Field Equipment Controllers
  • Johnson Controls MS-FEC2611-0U FEC26 Field Equipment Controllers
  • Johnson Controls AS-XFR010-1 Power transformer
  • Johnson Controls MS-NAE5521-1 Supports a LONWORKS trunk and two N2 trunks or two BACnet MS/TP (RS-485) trunks
  • Johnson Controls MS-NAE5510-1 NAE55 Network Automation Engines
  • Johnson Controls IOM3731 INSTALLATION MANUAL
  • ALSTOM MCRI1 - MODULE BOARD FOR SETTING SETTINGS AND CURRENT REGULATION
  • ALSTOM BCEA1 - TERMINAL BOARD OF 8 ANALOGUE INPUT SIGNALS
  • ALSTOM E64L1- LOGIC INFORMATION ACQUISITION BOARD
  • ALSTOM BCEL2 - TERMINAL BOARD FOR 12 LOGIC INPUT SIGNALS
  • ALSTOM BCSR1 - TERMINAL BOARD OF 8 LOGIC OUTPUT SIGNALS
  • ALSTOM ESVI1 - INPUT/OUTPUT BOARD FOR CURRENT AND VOLTAGE SIGNALS
  • ALSTOM MDEX1 – EXCITATION CURRENT MEASUREMENT AND CALIBRATION BOARD
  • ALSTOM IRVI20 - REGULATION INTERFACE BOARD
  • ALSTOM RDSP1 – BOARD FOR ADJUSTING DIGITAL SIGNAL PROCESSES
  • ALSTOM ARTN1 - DIGITAL INDICATION BOARD FOR VOLTAGE REGULATION
  • ALSTOM FRTN2 - BOARD OF DIGITAL INDICATION OF VOLTAGE REGULATION
  • ALSTOM CPRM1 - SINGLE-PHASE POWER REGULATION BOARD
  • ALSTOM AMS42 - POWER SUPPLY BOARD
  • DEIF PPM-3 SG PROTECTION AND POWER MANAGEMENT COMPLETE SET
  • DEIF PPM-3 DG Protection and Power Management
  • DEIF S8VK-S48024 Power supplies
  • DEIF S8VK-R20 Redundancy units
  • DEIF S8VK-T96024 Power supplies
  • Deif GPU-3 Generator Protection Unit 0-20MA
  • Deif Du-2 / Mkiii Multil neas Ppm Protecci n Y Gesti n de Energ a 100-690vac
  • DEIF AGC 222 & IOM 220 advanced genset controller
  • Deif Delomatic 4 DGU 0005 Generator Control System PCM 4-1, IOM 4-1, SCM 4-2
  • DEIF PPM-3-DG PROTECTION AND POWER MANAGEMENT MEAS.VOLTAGE:100-690VAC, 0.5MA
  • DEIF AGC Plant Management (Genset Controller) 100132445.10
  • Deif Delomatic 4 DGU 0002 Generator Control System PCM 4-1, IOM 4-1, SCM 4-2
  • DEIF 879.3C Dynamic Wind Sensor with MIC-4224 Display suit Marine
  • DEIF MDR-2 MULTI DIFFERENTIAL PROTECTION RELAY
  • Generator Control Unit Deif Delomatic 4 DGU 0001
  • DEIF DELOMATIC 4 DGU 0001 CONTROLLER
  • DEIF MTR-4-415 1200510024 Multi-transducer
  • Deif DPD 04057 Printed Circuit Board 1044230020F
  • DEIF AGC 252 advanced Genset Controller 2912420010.39 Options -C2-N
  • Deif AGC/GS/3.6 Automatic genset controller 600043767.80
  • Deif GPU/2/GS Generator Protection Unit
  • DEIF AGC-4/GS/4.4 Advanced Genset Controller Option-G5-G7-I1-M12-M13.6-N-J1
  • DEIF PPU-2-GS-100033222.50 PROTECTION AND POWER MANAGEMENT SYSTEM
  • DEIF PPU/2/GS Protection & Paralleling Unit + Operator Panel + Connector cable
  • DEIF PPU-2-GS-100059909.10 WITH DISPLAY AND CABLE PROTECTION
  • DEIF PPU-2-GS 600033613.10 WITH DISPLAY GENERATOR UNIT
  • Deif Delomatic-3 Generator Control Panel System Panel CP-1 | 1044220050D
  • Caterpillar Branded DEIF MCS2 Controller
  • Deif Paralleling & Protection Unit PPU-3 100121906.10 600V
  • A-B 20G11BC1K1JN0NNNNN PowerFlex Air Cooled 755 AC Drive
  • A-B 20P41AF452RA0NNN PowerFlex 452 A DC Drive
  • A-B 20GHAJC540JN0NNNNN PowerFlex Extra Tough 755 AC Drive
  • EPRO MMS6823 9100-00001-05 Displacement Monitor Module
  • GE LP-33 SERIES UPS DISPLAY & CONTROL PANEL LP33
  • GE CL06A300M IEC Contactor (50 Amp)
  • GE CR2962F2D Plugging Switch NIB
  • General Electric IC500A411DG2 Electrical Rectifier Semiconductor
  • GE IS200BICLH1AFE Interface Module 259B2431DB-G01 BICLH1A
  • General Electric 1253-0003-C4 Multilin Analog & I/O Board 369-A200
  • Ge Panametrics Crs-10-Mb Ultrasonic Flow Converter
  • GE PROPRIETARY IS215WEPAH2BB With IS210BPPCH1AD CONTROL BOARD
  • GE MULTILIN / 12P0-0001-P2 / Powerr Supply Board, 870500.DWG, 870501.DWG
  • GENERAL ELECTRIC PL19A129393G4 Auxiliary Receiver in Wall-mount Cabinet
  • GE CR306F002XAAA Nema-4 Coil 115-120V 60Hz 110-50Hz 600Vac Magnetic Contactor
  • General Electric 193x190bag02 ISOL P/S Board I93XI90BAG02 Computer board GE
  • GE Multilin / G6P3CH / Front Panel, G60 Generator Management Relay
  • GE MMY30-R1D26 DewPro MOISTURE TRANSMITTER
  • GE Drive Control Board 531X302DCIBDG2
  • General Electric SKLA36AT1200B Industrial Circuit Breaker 3Pole 600V / SRPK1200
  • GE CR2962E1A4 Plugging Switch 1600 RPM Max Speed Flange Mount
  • GE IS210AEACH1ABB Platine Card Sealed
  • GE EVEREST XLG3 Industrial Videoscope Sit 100-240V 50-60 Hz
  • GE DS215DMCBG1AZZ03B / DS200DMCBG1ALG board
  • 2H400489-0 REV 0 GE STATIC SENCITIVE BOARD A72 RPVM3
  • GE DM4E 1PC GE DM4E Ultrasonic Thickness Gauge Equipped with DA301 probe
  • GE DS200TCQAG1BED / DS200TCQAG1BED Analog IO Board
  • GE ENERGY PIB101C ANALOG I/O PIB MODULE PIB-101C
  • GE IC200CPUE05-HK VersaMax CPU Module IC200CPUE05
  • Ge Multilin F60 F6P3LA Feeder Protection System Brand
  • GE Intelligent IC695ALG112-DA RX3i 12 channel isolated analog input module
  • GE IS200WETBH1BBA Wind Turbine Control Panel PCB
  • GE Mark VI IS200HSLAH3A Genuine High-Speed Serial Link Interface Board
  • GE IS200TRLYH1BFD TERMINATION RELAY BOARD FOR MARK VI SYSTEM/JUA1221
  • GE XAMP-1-1-2-0 Adapter Converter With Enclosure
  • General Electric 1253-0002-C2 Multilin Upper Control Board 369-C100
  • GE Multilin 350 Feeder Protection Relay Controller Monitor Industrial Power
  • UR RHH / 12A0-0101-B4 GENERAL ELECTRIC MULTILIN POWER MODULE URRHH
  • GE MULTILIN / 12P0-0042-A5 / High-Density Input Board
  • GE MULTILIN / 12P0-0039-A1 / Digital Output Board
  • GE IS220UCSAH1A UCSA PWA Embedded Controller Mark VIe Gas Turbine Processor
  • GE RX3i PLC MODULE IC694MDL754-ED IC695MDL754
  • GE Multilin C60 Breaker Management Relay C60K03HKHF8LH6NM8LP6UUXXW7H
  • F31X139APMALG2 | GE Fanuc | Micro Application Board
  • GE HORNER ELECTRIC HE670ADC810D ANALOG INPUT MODULE
  • GE TRANSPORTATION LOCOTROL 7000069-910 REV. ZAE/D
  • GE Multilin / M6P3KH / Front Panel, M60 Motor Management Relay
  • GE 5CD124TP001B 2HP DC Motor 1750RPM 180V TEFC CD149ATC-PM
  • General Electric Ge RCC48 Lighting Controller Card
  • GENERAL ELECTRIC CR306F002XABA MAGNETIC STARTER
  • HE697THM160 GE Fanuc Series 90-70 Thermocouple Input Module, 16 Channel
  • GE 2298332 Digital Receiver and Filter II DRF2 2298333
  • GENERAL ELECTRIC DS3800NMEA1P1J CIRCUIT BOARD
  • GE 961529800 AVR Utilities Card S961529800 Prismic A30-M Controller
  • GE VMIVME 4140-000 VMEbus Analog Input I/O Module
  • GE VMIVME 3215-000 Computer module
  • GE IS215UCVFH2BB VMIVME-7650-83H 350-007650-83H C Control Module
  • GE VMIVME-7750 VMIVME-7750-834 350-027750-834 D Single Board Computer
  • GE V7668A-1310B0 350-9310007668-131020 Single Board Computer
  • GE IS220PRTDH1A 336A4940CSP6 Resistance Temperature Device
  • GE IS220PSCAH1A 336A4940CSP9 Serial Modbus Communication Interface Pack
  • GE SR745-W2-P1-G1-HI-A-L-R 745 Transformer Management Relay
  • GE SR745-W2-P1-G1-HI-A-L-R-E 745 Transformer Management Relay
  • GE WES13-3 2508-21001 Control Board Module
  • GE SR489-P5-H1-A20 Advanced Generator Protection
  • GE SR489-P5-LO-A20 Advanced Generator Protection
  • GE V7865-23003 350-9300007865-230003 M VMEbus Module
  • GE VME7865RC V7865-23003 350-9300007865-230003 M VMEbus Module
  • KEBA CU312/E Customized Controller
  • KEBA K2-200 CP253/W Input/Output Module
  • KEBA CU313 Large-Scale Complex Control Module