This document summarizes two Belden‑Hirschmann installation user manuals: RS20‑Basic (release 06‑2012) and RSP20/RSP25/RSP30/RSP35 (release 18. 09‑2021) fanless managed industrial rail switches for factory automation, power substation, railway and hazardous‑location applications.
1. Product Family Overview
RS20‑Basic
- Fast‑Ethernet only (10/100 Mbps), no gigabit ports
- Models: RS20‑0400…B (4‑port), RS20‑0800…B (8‑port)
- Redundant power input, DIN‑rail clip‑on mounting, fan‑less
- Management: Web‑UI, HiDiscovery, Industrial HiVision, local V.24 (RJ11 serial console)
- Ring redundancy for line / ring industrial Ethernet topology.

RSP20 / RSP25 / RSP30 / RSP35
- RSP20: Fast‑Ethernet; RSP25: FE + enhanced redundancy(MRP/PRP/DLR)
- RSP30: Gigabit Ethernet; RSP35: GE + enhanced redundancy
- Hot‑pluggable SFP slots, rear‑side SD‑card slot for ACA31 auto‑configuration adapter
- Multiple power options: CC / TT / K9 / KK; wide‑temperature variants S / T / E (conformal‑coated)
- Supports SSH, Telnet, RSTP, MRP, PRP, DLR; HiOS Layer2 / Layer3 firmware options.
2. Model Naming & Hardware Difference RS20‑Basic vs RSP Series
| Item | RS20‑Basic | RSP20‑25‑30‑35 |
|---|---|---|
| Release year | 2012 | 2021 |
| Gigabit support | ❌ None | ✅ RSP30/RSP35 support 100/1000 Mbps |
| SFP slot | Fixed DSC fiber port | Hot‑swap SFP sockets |
| Storage | No SD‑card | Rear SD‑card slot for ACA31 |
| Power options | DC only 9.6‑60 V DC | CC, TT DC; K9,KK AC/DC high‑voltage |
| Temp grades | Standard 0‑60 °C | S(0‑60), T(-40‑70), E(-40‑70 conformal coating) |
| Redundancy firmware | Basic ring | MRP, PRP, DLR optional variants |
| Explosion‑proof | ATEX II3G Ex nA IIC T4 Gc | ATEX / IECEx / UKEX II3G Ex ec nC IIC T4 Gc (only CC power version) |
RS20‑Basic naming example: `RS20‑0800M2M2SDAB`
> 8×10/100 M, 2×multimode DSC uplink, standard temp, DC wide‑range, CE‑UL‑ISA certification, Basic software.
RSP‑series naming example: `RSP35‑08033O6TT‑SE2S`
> RSP35(gigabit+enhanced‑redundancy), port‑count, SFP uplink configuration, power type TT, temperature grade S, coating, HiOS‑2S firmware.
3. Supported Interfaces & Media
1. RJ45 TP copper port: 10/100BASE‑TX / 1000BASE‑T, auto‑negotiation, auto‑MDI‑X, max cable length 100 m for Cat5e cable.
2. Fiber interfaces:
- RS20‑Basic: fixed DSC multimode 100BASE‑FX.
- RSP series: SFP transceivers: multi‑mode, single‑mode, long‑haul LH, Bi‑Di bidirectional 100 M / 1000 M.
3. Console: V.24 RJ11 serial port, 9600‑8‑N‑1.
4. Relay fault‑signal contact: potential‑free relay output for remote alarm monitoring.
5. RSP extra: SD‑card slot for ACA31 configuration backup / restore / firmware update.
4. Safety & Certification (Hazardous Location Critical Notes)
> ⚠️ For explosive‑hazardous locations (ATEX / IECEx / Class I Division2):
1. RS20‑Basic: certificate DEKRA 11ATEX0139 X, label `II 3G Ex nA IIC T4 Gc`.
2. RSP series: only CC power‑supply models are approved for zone‑2 hazardous area, certificate DEKRA 15ATEX0017X / DEKRA21UKEX0072X / IECEx DEK 15.0014X, marking `II 3G Ex ec nC IIC T4 Gc`.
3. Class I Div2 requirement: All connectors must be connected / disconnected under power‑off condition. Do not hot‑plug in explosive atmosphere. Equipment must install inside IP54 rated enclosure.
4. General approvals for both families: CE EMC / RoHS, FCC Class‑A, UL508. UL121201. IEC 61850‑3. IEEE 1613. EN 50121‑4 railway standard, DNV‑GL ship certification.
5. IP grade: IP20 (indoor cabinet‑mount only). Pollution degree 2.
5. Step‑by‑Step DIN‑Rail Installation Procedure
1. Unpack device and inspect for transport damage.
2. (RSP‑only): Insert ACA31 SD‑card if needed, lock thumb‑screw.
3. Mount onto standard 35 mm DIN‑rail: hook upper latch first then press down until click‑lock.
4. Connect protective ground screw first before any signal / power cable. Ground wire ≥1.0 mm² cross‑section.
5. (RSP‑only): Insert approved Hirschmann SFP transceivers.
6. Wire removable terminal blocks for power‑supply and fault‑relay contact, apply specified torque.
7. Plug terminal block back into switch housing.
8. Connect Ethernet copper / fiber data cables, follow EMC practice: separate power & data cables, avoid long‑distance parallel routing.
9. Fill in IP‑address / MAC‑address label area on front panel.
10. Apply supply voltage, wait for self‑test completion (approx. 60 seconds).
> Clearance requirement: keep ≥10 cm top‑bottom ventilation space; left‑right ≥2 cm for RSP models. Device must be mounted vertically.
6. Power Supply Variants & Terminal Wiring Rules
RS20‑Basic power
- Dual redundant DC input: 9.6 V DC ~ 60 V DC, SELV. Non‑load‑sharing; device selects higher‑voltage source when dual power present. Single‑power input triggers fault‑relay alarm (can be disabled in management software).
| Code | Input range | Terminal type | Redundant |
|---|---|---|---|
| CC | 24‑48 V DC | 2‑pin | ✅ Dual input, ATEX‑approved power variant |
| TT | 12‑24 V DC | 2‑pin | ✅ Dual input |
| K9 | AC 110‑230 V / DC 60‑250 V | 3‑pin | ❌ Single input |
| KK | AC 110‑230 V / DC 60‑250 V | 3‑pin | ✅ Dual high‑voltage redundant input |
> Terminal torque spec: power terminals 0.51 Nm; signal‑contact terminals 0.34 Nm.
Fault‑signal relay contact
Potential‑free relay. Relay opens when alarm condition occurs: power‑supply failure, port link‑loss, ring‑redundancy fault, self‑test error.
Rating: max 1 A resistive load. For hazardous‑location deployment strictly follow entity‑parameter limits in control drawing.
7. LED Status Indicators
System LEDs
- Power: Green = all power inputs OK; Yellow = only one redundant source alive; Off = no valid supply. Blinking 4‑times‑per‑cycle = firmware upgrade in progress (do NOT cut power).
- FAULT(RS20‑Basic) / Status(RSP): Red light = system alarm / fault‑relay triggered.
- RM (RSP‑only): Ring‑manager LED for MRP / ring‑redundancy status.
Per‑port LED (LS link‑status, DA / ACT data‑activity)
- LS green solid: link up; blink = port standby / port disabled.
- DA / ACT yellow flicker: data transmit / receive traffic.
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved