Overview
The Hirschmann MIPP (Modular Industrial Patch Panel) is a DIN‑rail‑mount industrial patch panel under Belden Hirschmann brand, designed for harsh‑condition industrial automation networks. It manages fiber‑optic and copper Ethernet cabling inside control cabinets and complies with IEEE 802.3 Ethernet standards。
Unlike traditional 19‑inch rack‑mount patch panels, MIPP adopts a fully modular building‑block design. The housing holds up to 6 single‑width modules. One double‑width module can replace two single‑width modules. Mixed fiber‑optic and copper modules can be freely combined according to project requirements. Cables can enter from top or bottom of the enclosure.
> Exclusive US‑only variant: IPDM1 / IPDM2 / IPDM3. empty copper CU‑module housings for RJ45 Keystone jack assemblies, only available for North‑American market.

Key Features & Module Types
MIPP supports multiple hot‑swap‑capable adapter modules for fiber optics and copper Ethernet.
Fiber‑Optic Modules
| Module | Width | Max Fiber Count | Adapter Type | Compatible Connector |
|---|---|---|---|---|
| LC Single Module | 30 mm | 12 fibers | LC Duplex | LC (IEC 61754‑20) |
| LC Double Module | 60 mm | 24 fibers | LC Duplex | LC (IEC 61754‑20) |
| SC Single Module | 30 mm | 12 fibers | SC Duplex | SC (IEC 61754‑4,‑19) |
| SC Double Module | 60 mm | 24 fibers | SC Duplex | SC (IEC 61754‑4,‑19) |
| ST Single Module | 30 mm | 12 fibers | ST Duplex | ST (IEC 61754‑2) |
| ST Double Module | 60 mm | 24 fibers | ST Duplex | ST (IEC 61754‑2) |
| E‑2000™ Single Module | 30 mm | 12 fibers | E‑2000™ Duplex | E‑2000™ (IEC 61754‑15) |
| E‑2000™ Double Module | 60 mm | 24 fibers | E‑2000™ Duplex | E‑2000™ (IEC 61754‑15) |
| Pre‑Terminated MPO Cassette | 30 mm | 12 fibers | MPO trunk + LC/SC/ST patch | MPO‑female trunk side; LC/SC/ST patch‑side |
Fiber‑optic modules include splice holders, fiber brackets, strain‑relief fixtures and cable glands.
- Single‑module: M16 gland, max cable outer diameter 10 mm
- Double‑module: M20 gland, max cable outer diameter 13 mm
- Internal fiber‑loop storage capacity: up to 15 meters of optical fiber.
- Supported fiber types: loose‑tube fiber, tight‑buffer fiber, semi‑tight‑buffer fiber.
CU Copper Module
- Single‑width 30 mm module, maximum 4‑channel Ethernet
- Interface: RJ45 Keystone sockets, compatible with Belden REVConnect industrial Keystone couplers
- Supported cable grades: Cat5e, Cat6. Cat6A, Cat7 (shielded / unshielded)
- Equipped with ground screw and cable‑tie bracket for field grounding and cable fixation.
IPDM Series (US‑Exclusive)
| Model | Quantity of empty CU modules | Max RJ45 ports | Operating temperature | Protection class |
|---|---|---|---|---|
| IPDM1 | 1 | 4 | ‑40 ℃ ~ +70 ℃ | IP20 |
| IPDM2 | 2 | 8 | ‑40 ℃ ~ +70 ℃ | IP20 |
| IPDM3 | 3 | 12 | ‑40 ℃ ~ +70 ℃ | IP20 |
Technical Specifications
| Item | Parameter |
|---|---|
| Mounting | 35 mm DIN‑rail (DIN EN 60715), tool‑free latch‑in installation |
| Operating temperature‑Fiber / MPO modules | ‑20 ℃ ~ +70 ℃ |
| Operating temperature‑IPDM series | ‑40 ℃ ~ +70 ℃ |
| Ingress Protection‑Fiber‑optic / MPO modules | IP40 |
| Ingress Protection‑CU copper modules | IP20 |
| Standards Compliance | IEC 61754‑2/‑4/‑15/‑19/‑20; IEC 60825‑1 laser‑safety; IEEE 802.3‑2009; UL 1863; RoHS 2011/65/EU & 2015/863/EU |
| Safety Warning | Laser radiation hazard on optical ports. Never view bare fiber or adapter ports with naked eyes or optical magnifying instruments. |
Step‑by‑Step Installation Guide
> Required tools: Phillips screwdriver, cable‑stripping tool; fusion splicer for fiber‑optic variants.
1. Unpacking & inspection: Verify delivery scope and check components for transport damage.
2. Module removal: Loosen 2 front‑mount screws and pull module forward out of housing.
3. Fiber‑optic module cabling:
- Pass fiber cable through cable gland, prepare sufficient stripping length for splicing.
- Tighten gland and secure strain‑relief fixture.
- Complete fiber fusion‑splice or terminate with Brilliance field‑installable connectors.
- Fix splice points in splice holder, store excess fiber on fiber bracket, seat connectors into duplex adapters.
4. CU copper module cabling:
- Terminate Ethernet cables to RJ45 Keystone jacks.
- Snap Keystone sockets into module cut‑outs; fasten cables with hook‑and‑loop strap.
- Connect protective ground wire between module ground screw and cabinet ground bar.
5. Re‑install modules: Slide modules back into enclosure and fasten 2 front screws.
wechat/whatsapp:
+86-181-44100-983
Email: kongjiangauto@163.com
Copyright © 2009 - 2026 Cld , All Rights Reserved K-JIANG All rights reserved