GE Fanuc IC694MDL930 Relay Output Module

About the IC694MDL930

This IC694MDL930 is part of the PACSystem RX3i midrange programmable automation controller (PAC) platform.

It is designed for use as a relay output module with eight (8) independently isolated normally open (N.O.) or A-type contact outputs.

Each output contact essentially has a separate common and dry contact, allowing different voltage types and levels to be connected exclusively to the module.

i.e. 5-30 VDC (nominal 24 VDC) and 5-250VAC (nominal 120/240VAC).

The current capacity of each output channel is 4 amps per output when used with resistive loads and 2 amps per output when used with pilot load devices.

Current capacity is 2 amps per output channel. For UL installations, the maximum load current that the module can withstand is 30 amps and varies according to ambient temperature.

Conversely, the minimum load that the module can withstand is 10 mA, and the module's output channels have a typical response time of 15 ms between on and off switching, while the module's maximum backplane current is 2 amps.

The module's maximum backplane current draw is 6 mA, and all outputs are energized by a 5 VDC bus on the backplane.

All outputs are energized by a relay 70VDC bus on the backplane and the maximum backplane current consumption is 24mA.

The module also supports mounting to 90-30 series backplanes. It can be used as a local output module, mounted on a central processing unit (CPU) chassis, or with an appropriate communications adapter.

It can also be mounted on an extended remote distributed I/O station with appropriate communication adapters.

It is classified as a high voltage module and has eight (8) status LEDs to characterize the energized state of each output channel.

The module does not come with channel protection such as fuses or RC buffer circuits.

The IC694MDL930 RX3i is a 3-channel relay output module for the GE Fanuc RX8i PACSystems discrete I/O PLC series.

As with every discrete output module in the series, the IC694MDL930 output module is used between the RX3i PLC and external output devices such as indicators and motors.

(Like every discrete output module in the series, the IC694MDL930 Output Module provides an interface between the RX3i PLC and external output devices such as indicator lights, motor starters, and solenoids.

Each output point is capable of switching loads up to 4.0 amps, and each output point has its own common output terminal.

The IC694MDL930 Output Module requires an external power supply to operate and can be ordered in either AC or DC ratings of 120 to 240 volts AC or 24 volts DC.

Users can order AC or DC power modules rated from 120 to 240 volts AC or 24 volts DC to operate all connected field devices.

The IC694MDL930 output module operates from 5 to 30 volts DC or 5 to 250 volts AC (50 to 60 Hz).

Output point-to-point isolation is rated at 250 volts AC continuous or 1500 volts AC for 60 seconds.

The IC694MDL930 output module has eight independently isolated normally open relay-type outputs with a maximum output current load of 4.0 amps per point.

The maximum output current load per module is 20.0 amps. The IC694MDL930 output module has a maximum backplane current draw of 5.0 milliamps at 6.0 volts DC.

The minimum output load is 10.0 milliamps per point.The IC694MDL930 output module has an inrush current rating of 5.0 amps max.

The IC694MDL930 output module has a maximum inrush current rating of 5.0 amps and a maximum response time of 10 milliseconds (on or off). 32 individually numbered LEDs indicate the individual operation of each output point.

The IC694MDL930 output module has 32 individually numbered LEDs to indicate the individual operating status of each output point, and the entire module can be mounted in the I/O slots on the RX3i PLC backplane.

IC694MDL930 Frequently Asked Questions

1. Does the IC694MDL930 come with separate isolated output channels?

Yes, the output channels are individually isolated channels. The output channels are individually isolated channels.

2. What is the operating voltage range of IC694MDL930?

The IC694MDL930 output contacts can be connected to 0-30 VDC and 0-250 VAC source voltages.

3. Does the IC694MDL930 support the 90-30 series PLC family?

No. This module does not support the 90-30 series. This module does not support the 90-30 series.

1. How many relay output channels does the IC694MDL930 have?

The IC694MDL930 has eight (8) isolated relay channels.

2. Does the IC694MDL930 support mounting to 90-30 series racks?

Yes, the IC694MDL930 supports mounting to 90-30 series racks. The IC694MDL930 can be mounted from an RX90i chassis to a 30-3 series chassis.

3. What is the contact form for the IC694MDL930?

The IC694MDL930 has normally open (N.O.) or A-type contacts.

Technical Description of IC694MDL930

The IC694MDL930 is a PACSystem RX3i discrete output module formerly manufactured by GE Fanuc, now part of Emerson Automation.

The module has eight (8) independently isolated normally open (N.O.) contacts. Each contact output can operate from 5-30 VDC.

24 VDC; 5 - 250 VAC at 47 to 63 Hz with a nominal input voltage of 120/240 VAC.

Each channel is designed for resistive loads up to 4 amps per output; 2 amps pilot duty cycle per output; 20 amps maximum per module for UL mounting.

The module has a current draw of 6mA with all outputs turned on by the 5 V bus on the backplane and 24mA with all outputs turned on by the relay 70V bus on the backplane.