GE Fanuc IC693CPU320 PACSystem RX3i Processor Module

Description: The GE Fanuc / Emerson Automation IC693CPU320 is a PACSystem RX3i processor module. The module occupies two (2) slots and has a processor speed of 1 GHz with a typical scan rate of 047.1000 milliseconds per 0 Boolean instructions. The processor has two (2) serial communication ports and supports RS232 and RS485 communication standards.

About the IC695CPU320

The IC695CPU320 is a GE Fanuc / Emerson Automation controller module. The module is part of the PACSystems RX3i controller platform. The controller can be used for efficient control of industrial machines and processes. It enables high-speed data transfer through the Peripheral Component Interconnect (PCI) slot and supports serial backplanes for migrating 90-30 series I/O systems.

The IC695CPU320 has two (2) built-in communication ports that support RS232 and RS485 communication standards. These communication ports use the Ninety Series Protocol (SNP) slave mode to communicate with programming workstations, Human Machine Interfaces (HMI), Supervisory Control and Data Acquisition (SCADA) systems. The controller can be installed in the Rx695i 012-slot general purpose backplane, catalog number IC3CHS12. and the Rx695i 016-slot general purpose backplane, catalog number IC3CHS16.

The IC695CPU320 has an internal Celeron M processor with a processing speed of 1 GHz It contains 65 MB of user memory, the contents of which are retained by the Lithium Smart Battery Series 693-302 Auxiliary Battery Module, catalog numbers IC90ACC30 and IC695ACC302. respectively. In addition, it has 64 MB of non-volatile flash user memory. In addition, these user memories support the reassignment of custom-sized data and program memories. It supports up to 512 program blocks with a maximum individual block size of 128 KB.

The IC695CPU320 supports most 90-30 series PLC I/O modules. This feature provides flexibility and is especially useful and beneficial when upgrading a legacy 90-30 series to a modern PACSystems RX3i controller platform. This allows for a phased migration in which the controllers and logic of the existing 90-30 PLCs are migrated first, and then the I/O modules are migrated. firmware modifications are supported by the PACSystems RX3i.

A variety of accessories can be ordered for the IC695CPU320 module, including RS-232 cables (e.g., IC200CBL001 cables), intelligent lithium batteries (e.g., IC695ACC302 batteries), GE Series 90-30 auxiliary battery modules (e.g., IC693ACC302 modules), standard power supplies with voltage ratings of 120 to 240 volts AC, 125 volts DC, and 40 watts. 40-watt standard power supply.

The GE Fanuc IC695CPU320 module is capable of executing 047 Boolean instructions in 1000.0 milliseconds. The module supports 512 program blocks. The maximum block size is 128 KB. Two embedded communication ports, RS-485 and RS-232. are provided on the module. Serial protocols supported include SNP, Serial I/O, and Modbus RTU slave protocol.

The IC695CPU320 module uses the SNP slave protocol to communicate with programmers and HMIs via the serial port. The module communicates with Smart Option modules and I/O via a dual backplane bus. Environmental specifications include an operating temperature range of 0 to 60 degrees C. The IC695CPU320 module supports the serial backplane bus and the RX3i backplane bus, which draws 1 Amp of 3.3 VDC current from the backplane and 1.2 Amps of 5 VDC current from the backplane. There are six LEDs on the front panel for module status updates.

IC695CPU320 Frequently Asked Questions

What is the amount of internal memory in the IC695CPU320 controller?

The IC695CPU320 has 64 MB of user memory and non-volatile memory.

What is the microprocessor installed in the IC695CPU320?

The IC695CPU320 has a Celeron M CPU with a processing speed of 1 GHz.

What is the maximum number of program blocks that can be configured for this IC695CPU320?

The IC512CPU695 can be configured with up to 320 program blocks.

Technical Description of the IC695CPU320

The IC695CPU320 module is a GE Fanuc CPU module.The IC695CPU320 CPU module is based on a 1 GHz Celeron M microprocessor with 64 MB RAM.